Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hello,
I have a custom board which works fine with SoftDevice+Application , but if i Combine a boot loader hex that i complied it doesn't work. But the same ( bootloader...
I found and implemented an example that gives me a decent idea of how to go about polling for data with the UART/FIFO. However this doesn't give any indication of how to use...
Hi.
Trying to set up the Ubuntu development environment for you nRF52 development kit.
I followed this tutorial:
devzone.nordicsemi.com/.../
Stuff done so far:...
I am using the nRF51822 chip. The RAM memory is composed of two blocks (0 and 1) of 8kB each, divided into 4 sections : Call Stack, Heap, Application, and SoftDevice.
If...
Hello,
I have migrated to the latest version of the sdk11. However, I get a nrf error 4 when I call sd_ble_uuid_vs_add. Multiple people on this site have been having this...
I am trying to port blinky_blank (no SoftDevice) to my target and started by creating a custom_board.h header file with correct GPIO pins for the LEDs and duplicating blinky_blank_pca10040...
Can anyone help me reading IO capability in Android? Basically there is a known bug in some Android versions across different manufactures where Android reports wrongly IO...
I want to use chacha20 cypher to encrypt and decrypt a 64 byte message and send it over BLE. I tried using wolfSSL, cifra both of which provides the implementations but there...
Hi,
To measure the transmitted RF power (to reach EN 300 328) we Need some ATT commands to set fix channel and maximal output power. In additional we test the EN 55022...
In this previous discussion on minimizing power consumption on the NRF51-Dongle, it says:
You are using evaluation kit or
development kit and LEDs are connected
on...
My system is a BLE peripheral with 2 states. There is a characteristic that represents the state, and it can take 2 values: 0 and 1.
You can read the state, write it (force...
When the supply voltage drops below 0.6V and then get back to 3.3V the nrf51822 starts up in an undefined state and often some flash pages are corrupt after that. Is this...
Hello,
We're currently running softdevice s310 v2.0.1 with SDK 7.1.0 on the nRF51422-QFAAE0 (ie. rev 2). We're planning on upgrading to the nRF51422-QFAAF0 (ie. rev 3)...
