Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Chip: NRF51822
Per the documentation the band gap voltage is 1.2V however on my board when I apply the voltage 1.5V to AIN2 i read the following value from the ADC: 209...
I am completing a schematic using the nRF51822 part. I will be supplying the part with a 3.3V supply. I will use one of the ADC inputs to sense battery voltage (up to 10v...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
I was using nRF Master Controller app on Samsung S4 to connect to my Ble device. However, after connected a while, the device will be disconnected automatically while I was...
I'm getting started and have an overwhelming amount of stuff downloaded which I'm trying to make sense of.
Which of the examples in the nrf51 SDK use the Softdevice and...
Hi,
I'm using a NRF8001 shield with an Arduino Leonardo, everything connection wise seems to be working. I'm using the "ble_my_project_template" and uploading various services...
I install the j link driver for mac(4.78k),connect the ek,but can't recognition it:
Sens-Macbook:~ sen$ JLinkExe -if SWD -device nRF51822
SEGGER J-Link Commander V4.78k...
I'm usually cleaning out the older manuals when downloading new ones from the web site. Unfortunately the new EK user guide 1.2 doesn't show how to connect the nrf51822 UART...
I would like to use an idle loop for non critical tasks. Is there any way this can be done with the scheduler implementation? I don't want this to be time based, I just want...
I have worked with nrf24l01+ devices. In my project include single PRX with 100 PTX. Objective of this project is all PTX send packet to one common PRX device & PRX send ack...
I have the simple UART example working with the nRFgo motherboard laid out as described in the SDK docs, with 2p connectors on the RS-232 P15 and the SDA and SCL pins of the...
Hi All,
I'm just starting to use the 51422 DK and I do as the nRF51422_Developer_Kit_User_Guide,I have flashed the broadcast_tx of the ant_broadcast project in SDK and...
After I download NRF51822_0.9.0.HEX in PCA10001 v2.1, but the MCP cannot work. Anyway, PCA10000 is working fine. Do you have any solution about this? Thanks.
