Hi,
I’m streaming high-rate sensor data over BLE with an nRF52840 running NCS v2.9.0.
Data rate: 1 kHz, ≈ 8 400 B/s
Packing: 5 samples → 42-byte packet, pushed...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hi Nordic Team,
I recently joined the DevZone and I’m interested in contributing to the blog. I’d like to write technical articles and tutorials related to Nordic products...
Hi,
I am programming with ncs v2.9.0, nrf52833 chips.
I am going to get pc keyboard led state in my custom board throutgh BLE.
This is my report map,but cannot get data...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi!
I have AD5611 DAC connected to nRF51822 by SPI.
In DAC datasheet we need to send data by MSB first order.
Data packet is 16 bit length.
I feel variable uint16_t...
Hello,
I use the pca10040 and the problem is in 14.0 eaxmple ,when I push the button switch the protocol mode like : ble->gzll->ble and then I find the example loop into...
Hello,
based on the saadc example of SDK 11 I am trying to change the code to use the SAADC's local timer to sample the input given number of times (10 times for the below...
Hi,
well I struggle with another problem right now.
In case of some errors, I use 'sd_nvic_SystemReset' to reset the system.
But the WDT is used in the application. Thus...
Hey guys,
how can we use DSP math functions on the nRF52832 little monster?
Is there somewhere some documentation?
What about power consumption and performance?
...
Hi, I'm using blinky from the SDK12 as an example here with a nordic nrf51 DK (pca10028, onboard nrf51422) which I am using as a programmer with a custom board (with a nrf51822_XXAA...
Hi guys, just signed up here for some help.
I was learning how to develop a project with nrf51822 core chip. The one I'm using is this one . I also have a DK for the nrf51...
I'm attempting to change phy in a program based on the UART example and am following the same process used in the att_mtu_throughput for changing PHY.
Calling sd_ble_gap_phy_request...
Hi,
I'm using nrf52 + SDK11 + softdevice 132 2.0 and trying to integrate
the OTA dual bank bootloader. Using the nrfjprog tool I program the
softdevice + bootloader....
I am using the nrf52832 soc, and have a requirement to run the device in low power mode and using the timer with a timeout value in days? how can I do so?
Sample code would...
I want to read data, advertised by a bluetooth beacon.
I have made this work before with SDK v14 using NRF_SDH_BLE_OBSERVER() to register a handler function to handle BLE_GAP_EVT_ADV_REPORT...
As a complete newbie to this a bit of guidance would be really helpful to point me in the right direction.
I want to create a simple device with a couple of switches (physical...
Hi Nordic community,
I'm sending several packets from nrf51822 (custom board) to Android application. At the moment I want to configure the sensor by sending commands from...
hi,
I tried to recover custom nrf52 board by nrfGo stuidio,and it failed,the logs as below:
------------------------------------------------------------------------...
Hi All,
I'm using a sdk11 and i have started using the glucose profile example to use a peer_Manager.
I have modified it to have a just work behavior. It works correctly...
