Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
hi i am using nrf51 development kit. i have gone through nordic development zone tutorial to use Eclipse IDE. build was successful it is creating release folder in which i...
We are interfacing serial flash using SPI interface and use nordic nrf52 nrf_drv_spi.c as the library.
We have taken a look at nrf_drv_spi.c, and it seems in the api nrf_drv_spi_transfer...
I am using Nordic nRF51 Development Kit with SoftDevice_130_2.0.0.I tried to run the SDK 11.0.0's example "examples\ble_peripheral\ble_app_gls\pca10028\ser_s130_spi" from...
As Nordic newsletter, s132 v3.0.0 softDevice have been released, I have a question that: if I want to use new feature in s132 v3.0.0 like DLE or privacy, does Nordic need...
I am trying the tutorial Radio Notification and was following the patch from Ble_radio_notification wont compile . The radio notification init comes right after the ble enabling...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board. I want to know how to control the timeout from when the program goes from Bootloader...
My set Up:
TI as Peripheral,
Android as Central,
Nordic as Central
I am doing directed advertisement using TI as peripheral.
Using Andriod as central, I am successfully...
I am trying the ANT-OTA DFU Update using an ANT Stick and the nr51422 pca 10028 board.Using the OTA Tester (s210), I am currently doing an OTA Update with the s210 dual bank...
Hi all,
I have an STM32 connected to an nrf51822 via uart, and I want to do a firmware update of the stm via ble.
Therefore, I would like to take advantage of the Master...
Hi
my idea is to open and close pipes identified by BLE address of device.
Currently I enable ESB on BLE disconnect using timeslot API.
How can I do this "on the fly...
I'm testing with Soft Device 8.0.0, ble dfu operation with single bank, nRF toolbox on Android version 1.13.1 (installed on 5/11/2015). I generated a zip distribution file...
Hi,
is there any way to connect at the same time multiple devices with Android/iOS nRF UART app to an nRF52832 with ble_app_uart example?
I was thinking about adding advertising...
HI all,
I am setting these parameter as follow in my ble_app_template sample.
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) /**< Minimum acceptable connection...
Hello everyone
I'm the proud owner of a nRF52 Prev. DK and trying to get my project to work. I would like to sample 3 to 5 analog signals using the ADC on the DevKit, followed...
