Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
hi.
in s110 there is no problem but when use example ble_ant_app_hrm in s310 nrf51422 the ble getting error.
its error code is 536881912 :( .
in debug point error ocure...
hi.
i wrote a program in s110 and it work fine . in it i creat my own service .
but when i want use my service in s310 softdevice in this line i get error forbiden or error_code...
How can I flash SD110 and Serialization on Wavetek's WT51822 shield? I am working with an ST nucleo64 and mean to use STlink for flashing.
I found an application note from...
what is the procedure to find connected device is bonded or not, should i store the device, application or service context in persistent memory to help recognizing bonded...
Hi Nordicsemi,
I am working on peripheral BLE device, the device accessible from smartphone i am also writing the smartphone app, i want just my app to be able to connect...
Just received my Nordic nRF Smart Beacon Kit and was following the instructions in the User Guide to get setup. I inserted the battery into the beacon and there's an LED flashing...
My project is working but nRF connect does not seem to show it properly when advertising. It shows up for a moment then dissappears then shows up a while later on the RSSI...
I did try to SPI example in nRF5_SDK_11.0.0
But, I saw print in serial terminal only one-byte log which is NRF_LOG macro.
Basically, It SPI example included app_uart.c in...
Can't transmit a modulated carrier for FCC testing
part: nRF52832
We are writing our own firmware to support FCC testing. We have been successful at controlling the chip...
Our project use 51822 and another MCU stm32 to transmit heart rate data by uart. then 51822 SPP heart rate to smart phone APP. Now, We meet a issue that 51822 UART will crash...
Hi,
I just found what looks like a bug in ble_nus.c in SDK12 - not sure how to report it so I'm just doing it as a question/answer combo.
Basically:
Connect to...
Hi,
I'm developed a custom nRF52 board, and the main method to reset is via power cycling the power source (battery). Using GCC, should I still keep:
CFLAGS += -DCONFIG_GPIO_AS_PINRESET...
Now, I'm using the SDK12.1.0 and the device is NRF52832, I trying to use the secure DFU bootloader, when I open the Project Nordic provided(PCA10040 Debug) and build it, the...
Hello,
I have a PCA10028 that I want to use as a sniffer using the NRF Sniffer firmware. I tested it in macOS and it's working. The problem is that I also want to connect...
I put my code before ble_stack_init()
reset_reason = NRF_POWER->RESETREAS;
NRF_LOG_PRINTF("reset_reason: 0x%08x.\n",reset_reason );
//NRF_POWER->RESETREAS = 0xffffffff;...
