I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hello ! Can I read with SPI registers without any problems from inside a ble_event_handler or a timer_handler or should I expect to have problems due to interrupt priorities...
In the SPIM section of the product spec for the nRF52832, the spec describes sending the STOP task (even if the peripheral is already stopped) and receiving the STOPPED event...
Hi,
If I have a custom board with the NRF51822 operating at VDD=2.4V, would it be possible to program the part using Segger JLINK Lite programmer that comes with the dev...
I am attempting to update the firmware on a DFU V1 device using javascript inside of a cordova app. Due to the time it takes to roundtrip the write response it is going to...
Hello again,
Edit:
I am now only getting these 4 errors after enabling the clock in the nrf_drv_config.h file
I may be able to track down the problem myself if someone...
Hi,
I'm trying to get NFC working on a PCA10040 dev board. Using the nfc/record_url hex file it works fine, so the hardware is obviously ok.
However, when I use the...
I need to save data to flash on an nRF51422. I already have same basic thing working on an nRF52, so I figured the same API calls would work, but they don't. My main symptom...
I have an application that bonds to mobile devices and encrypts the connection on both Android and iOS. What I am noticing though, is that after each time I use the DFU to...
I want to stop advertising for 8 hours
but when I use
sd_ble_gap_adv_stop();
sd_ble_gap_connect_cancel();
It starts advertising after 1 or 2 secends again.
I think...
Hi,
I followed the tutorials shown below:
infocenter.nordicsemi.com/index.jsp
I downloaded SDK v11.0 and loaded S130 SoftDevice on my nRF51 DK. I use Keil uVision 5...
I am working on a bootloader for a client. I’ve been looking at the DFU example that Nordic has. The BLE version of the DFU needs to have the special format using the “nrfutil...
hi:
I use bootloader example of sdk 9.0.0 ,most cases worked fine, but I got gatt error sometime when I begin DFU. I had changed the dual_bank_ble_s110 into sigle_bank_ble_s110...
The nRF51 reference manual says that GPIO PIN_CNF registers are retained registers and that "a retained register is a register that will retain its value in system OFF mode...
Hi,
I'm trying to add second service on the fly, while SD running. After adding it, I'm trying to send service changed notification, but it don't work. Below is code used...
