Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I'm working on ble_app_hrs_c application with Nordic beacon.
Using nRF51822 Ver.H0 with S120 and modified to using Internal 32.768KHz RCOSC and UART at 115200bps...
Hi guys,
I'm playing with a beacon kit, nRF51822-BK.
It works out of box, no problem but I have a simple question. One of our customer asked me if is possible to control...
Hello,
I am using nrf51 SDK version 10.0.0 along with the nRF51822, and I believe I have found an issue with a macro that is supposed to check the correctness of a bit...
Hi All,
Another question for those out there much smarter than myself...
We're developing an application using nrf52, sdk11 and softdevice s132 2.0.0 and have been using...
I see it is advised not to just stop a timer, but to also shut it down for certain of the nRF52s. What call is necessary to achieve this since I understand it is deprecated...
I want to read the onboard (dev board) buttons which i believe are P13-P16. I want to know the working code.
uint32_t app_button_is_pushed ( uint8_t button_id,
bool *...
I am trying to estimate the memory usage of the s132 v3.0.0 running on a nRF52832. I am interested on acting only as a peripheral with one link at a time only. From app_ram_base...
Implementing my own protocol stack with low-level programming of the radio, can I broadcast by simply programming all units to receive the same address?
No addresses (such...
Hi,
I am trying to use the sdk version 9 for the NRF51 to take ADC samples and trasmit it over BLE over UART found in the link: github.com/.../nRF51-SDK-9-0-0
I downloaded...
For example,
CFLAGS += -DCONFIG_GPIO_AS_PINRESET
CFLAGS += -DNRF52_PAN_12
CFLAGS += -DBLE_STACK_SUPPORT_REQD
Where are -DCONFIG_GPIO_AS_PINRESET, -DNRF52_PAN_12...
Hi,
I faced a strange kind of issue while i was burning the same code on nrf51442 and nrf51882 chip. The code is running fine on the nrf51442 chip but the code wasn't running...
My µvision crashed during programming and will no longer respond to trying to program it. It boots into the bootloader mode. My computer sees it but the precompiled binaries...
Hi ,
I am using nRF51 SDK with S130 soft device lib, and it is running well when downloading the example of ble_app_uart. But when I want to modify the service UUID from...
Hi,
I'd like to check the battery level in my BLE device, and I can set a timer to handle the checking, however this means that Timer 1 would need to powered up, and hence...
