Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hi guys,
Right now, I'm trying to do some throughput measurements via the experimental ble_app_att_mtu_throughput example. This using the SDK 14.2 and S132 on two nRF52832...
Hi,
I have seen some curious behavior with the FDS module. I'm using nRF5SDK 14.2.0 with s140_nrf52840_5.0.0-2.alpha, with FreeRTOS. In short: In some cases it seems that...
Hi!
I want to get infinite advertising.
My advertising gets timed out in 180 sec.
I have set to Fast Advertising Mode.
Below is my code
static void ble_evt_dispatch...
Hello,
I'm following this BLE services tutorial . I have added the functions required to create a service.
In the our_service_init
void our_service_init(ble_os_t...
Hi guys,
Currently, I am developing a application on nrf51822 which requires writing values on flash to store in case of power down. However this values need to be updated...
I have a nRF51822 smart beacon kit and a ST-LINK V2. I read the documentation found on nordic's website, downloaded all the programs that the documentation requested etc....
Looking through the ESB implementation in SDK 14.2, nrf_esb.c I notice it uses
#ifdef NRF52
on several places. In nrf.h, the "old" NRF52 gets re-defined as NRF52832_XXAA...
I tried every configuration I can think of to reload firmware on the DK with JLINK drive when PPK is piggybacked. The only way I can get the firmware to load on the DK is...
Hey, I'm running the ble_app_hids_keyboard example. I would like to modify it so that once I have a connection to a device I can press a button and go into advertising mode...
I have questions about nrfutil's latest.exe. Dose it able to do OTA DFU over BLE for every SDK version's firmware?
I have been trying do OTA DFU using Master Control Panel...
Hello,
I've the nRF51 DK which works fine because I managed to upload BLE Softdevice and application with nRFgo Studio. But I cannot get the MCP (Master Control Panel)...
Hi,
I'am working on a project that use the NRF52832 and i can only use P.23 and P.12 on my custom board because they are already wired to a connector, others pins are not...
What is pinout for nrf51822QFAA ?
Everywhere is description Generals Purpouse and I don't know which pin is I2C or SPI.
I don't want long find in example source codes.
Am Working on android application where the Requirement is User will get a Notification about firmware update having YES or NO options.If the user selects the YES options...
hello,
I want to make a beacon with NRF51822 chip.
But now i have a trouble:
In normal working mode, after i stopped the advertising with sd_ble_gap_adv_stop() ,i cann...
