I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I've implemented a peripheral with bonding support by the peer manager. Additionally the device should scan for bonded devices by using a whitelist. I used the function...
Hi,
I'm trying to compare two RC networks by using GPIOTE, PPI, a Timer and the comparator to measure the time needed for a charge and discharge cycle for each of the networks...
Is it possible for one Arduino Uno to have a BLE nRF8001 module and a nRF24L01+ module wired to it (allowing each module to communicate simultaneously)? According to the wiring...
We are trying out the new nRF5x SDK v12 and it looks like the previously working ble_app_hids_mouse example is broken now.
It compiles successfully, but as soon as we try...
I have observed that the Radio Notification from ble_radio_notification.c becomes inverted sometimes. I saw this post about the same problem:
devzone.nordicsemi.com/.....
I would like to use nRF5 SDK for IoT with some functionalities (e.g. SEGGER RTT) from nRF52 SDK. Can I just copy desired modules to my SDK for IoT and suppose it'll work?...
Hello,
For some industrial reasons, I need to store the passkey in the flash of the nRF5 during production and retrieve it at run-time.
I would like to know if there...
Hi,
for our prototyp we use a NRF52. When i flash the device, it will always be go in sleep mode after a duration of time and stay in there.
Is there an interrupt which...
Hi all,
i am using V11 sdk.
i want to send data "hello" in beacon application.
how to add that feature.?
any function calls are there?
-Thanks in advance
Hi,
I am using a PIC microcontroller in my project (18F family) and I would like to know which are the tools needed to begin development with the NRF80001.
I already...
Hello,
I am doing a project using nRF51822, s130 and SDK 11. I have modified the example ble_ap_hrs_rscs_relay.
My problem comes when I try to update a notification...
Hi,
I am porting our application from SDK10 nrf51 to SDK12 nrf52. The application takes use of a serial console accessible over UART.
I notice the new logger module...
Hi all,
i am V11 sdk.
Task:
i want to send and receive data without connecting the nordic_uart example
i.e ble_uart eg is send and receiving the data when we press...
Hi all,
i am using V11 SDk,
my task:
One board should broadcast continusuly.
if there is any neighbour is broadcasting ....then that will capture those data too...
Hi,
I am working on adc module of nrf51,through adc i am taking data and storing it in array.now i have to crossexamine this adc data with the prestored data and have to...
