I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
i've got problem with spi master connection, im trying to set leds via SPI on DWM1000 module, i've checked through advertising that spi_master_send_recv() sends correct values...
I need to keep track of an integer array in an nRF51822 BLE peripheral (SoftDevice 8.0.0) between power cycles, and I try to use persistent storage manager for this task....
Hello,
I'm starting a new project on mbed with nRF51422. I'm a little bit lost about how to modify nRF51822 project to use S310 (ANT+ and BLE) package instead of S130 ...
I'm developing a BLE application where I want my slave/peripheral to sleep as much as possible to save power. I'm not sure how to set the connection parameters.
I'm looking to migrate from SDK 6.1 to SDK 9.0, using GCC and Eclipse. Any pointers would be welcome.
Also, I'm hoping to start using the OTA DFU. Once again, if there are...
I want to capture connection packets between BLE Master and Slave
(this part is easy) but also capture any advertisement send out by slave
at the same time.
Our BLE peripheral...
I brought up the Template example on the S110 for nrf51822 and as an exercise, attempted to add in the battery service. I just did a few simple things:
in main.c:
-included...
Hello, I want to using nrf51 dk with uart communication.
So, I want to know how connect both PC and nRF51 DK.
I've download with 5pin connector to USB.
In former days,...
hi,
i have meet an issue,when my pca10028 board was advtersing it can be found by the android app which provide by nordic.But it can not be found by my mobile phone.So,i...
I have compiled the bootloader and the application firmware with keil.
When I install the application firmware by means of the bootloader dfu ota.
The bootloader launches...
Hi,
Unable to locate the source code for "UART/Serial Port Emulation over BLE"?
The documentation for this is available in this link - developer.nordicsemi.com/.../a00072...
Hi, i try to understand how to use power down modes. But i have a problem in the example gzll_device_w_power_management of nrf24le1 sdk. Before enter register retention in...
I just started using RTT because I needed to trace execution through some ble events and the uart could not keep up.
It is very nice, but I am used to frequently resetting...
Hi all,
I'm trying to use the experimental ANCS example with an iPhone iOS 8.3. My Nordic SDK is 8.0.
The sequence is the following :
Flash the example on the dev...
Hi,
I'm looking at interrupts from three different GPIO-pins. I'm setting it up like this:
static void gpiote_init(void)
{
uint32_t pins_low_to_high_mask = INTERRUPT_1...
