Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi,
I want to know how sd_ble_gap_authenticate api works.After executing this api, what are the events invoked at peripheral end. Is there any event that blocks CPU or...
We are designing product based on nrf2401A
The problem that we encountered was that the nrf2401A forgeted configuration data, was it possible ?
we use our product in highly...
Hi,
I am using the nrf51822 in an intermittent high-current application where if the battery is close to dead, will sometimes cause the chip to reset because the voltage...
I am using SDK 8.1.0 and Eclipse on a Mac. I am having difficulty flashing my app that uses the nRF51 sdk onto nRF51. I am using JLink
I assume I need to flash two things...
Hi nrf51 developers,
I'm developing multiprotocol application by combining BLE and a proprietary protocol. I'm using concurrent multiprotocol timeslots API. Started with...
I am new to programming both the nRF518122 as well as the Cortex-m0. As I have been building and running the example apps that come with the nrf51 sdk, I run across the CMSIS...
Hello,
I'm developing device application where I need:
peripheral (advertising also when in connection)
central role
whitelisted connections
maybe some encryption...
Hello,
I'm trying to do some simple printfs to hyerperterminal as a way to debug my code. I have used the uart example init code but nothing prints:
void init_uart(void...
I have enabled data ready interrupt bit and also enabled the fifo bit and also enabled gyro_fifo and accel_fifo bits in mpu6050 so that when data ready interrupt occurs the...
I have a nRF51DK. The Softdevice on the board is S110.
I load the ble_app_template from the SDK 8.1 on the chip. It builds with success. Now with the MCP I am able to see...
I'm now using the lastest SDK 8.1.
I found that if I call app_button_enable() after app_button_disable(), app_button_enable() would not function again.
But if I changed...
Hi all,
I read that the nRF51822 comes as a blank chip from the factory, and this means that we have to program the SoftDevice ourself. I am wondering if this is the only...
Hi,
I'm using the Rigado BMD-200 Eval Board with sdk 8.1 and am running the ble_peripheral example titled ble_app_uart. I am using my iphone and the nRF UART app to communicate...
