After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
I have problem with nRF51 antenna orientation. I used nRF51 developement kit (mKIT) board and I had problem with communication if I just change a little inorientation...
Can I change the shared channel address (first one or first two bytes in the message) when the channel is open?
The manual says after opening the channel, send a broadcast...
Hi,
I rely on twi_hw_master (from sdk 7.1.0) to communicate with a sensor. It works without any issues without the SoftDevice. With the SoftDevice enabled, using TWI causes...
Would you recommend purchasing Red Dear Lab Development Board? Or should I get an EVKIT from Nordic Semiconductors?
Nordic Semiconductor eval kits are expensive and shipping...
I want to have it wireless capabilities into the cable, the receiver and transmitter antenna ports with shielded wire connected directly, so there will be a wireless signal...
hi, guys.
I'm prepareing the Korea certification, KC, with nRF51822 BLE system.
I'm progressing to get KC by certification agency.
Today, They will have RF signal test...
I was comparing the binaries for the S120 and S110 stacks and see the MBR is different.
I was under the impression that the MBR never changes and was thus expecting it...
Hi Nordic
We want to test radio parameter through IQxel . Now,we need a application software to control nrf51822(TX,TX,outpower,channal and so on ) . Can you recommend...
I'm using the example code for simple device/host Gazell in SDK 7.1.0 as my starting point for my application.
My program runs for a second or two, then ends up in the...
Hi
I am new to programing low energy devices. I got a Blend Micro from RedBearLabs. I am using the
nRF Master Control on android to connect to it. I am able to change...
As I create my first 'profile document', it would be nice to read over some examples. My only knowledge of this document comes from nAN-36, section 2.2.2.5 :
A profile...
Hi
in the SDK 7.1 examples, there are examples about how to use the hardware peripherals, and examples on how to use the BTLE stack, but nothing combined.
How do I combine...
Hello, I've started bluetooth development with nRF51 DK since yesterday.
My devlopment platform is KEIL-MDK(v5)
Yesterday, I just tested my board, download the blink...
