I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Is it possible to have 1micro second interrupt using timer 1?
I am unable to achieve it.
If I try for 4micro second, I observe toggling of pin at 8 micro seconds?
...
Some examples require SDK 7.1, while the newer tutorials use SDK 8.0. I'm not sure how to switch between the SDK versions in Keil. I see the below lines in my include paths...
Hi.
Currently, the following results came out in the power-saving support .
■Our App
・Advertising Status
1.04mA ~ 1.13mA
・Connection Status ★1
1.044 ~...
Hi.
After stopping the Advertising,I measured the current.
For some reason, usually it is consumes about 1.1mA.
Because too large current consumption,
As a result...
Hi I using nRF51822, and want to know about the Nordic driver support LMP feature
Do you have any document about driver support? Or any software development document except...
Hello, I need to create a high resolution/high frequency PWM signal on the nRF51822. I have been using the new PWM library in the 8.1 SDK and can't quite get there.
From...
Hello. After a couple of s210 and s310 projects, I am attempting an s120 project. I built a client SDK but sd_nvic_EnableIRQ returns error code 0x2009 or NRF_ERROR_SOC_PPI_INVALID_GROUP...
I'm running the "Beacon Application for Eval Board" example for the S110 soft device on an nRF51822.
( devzone.nordicsemi.com/.../a00070.html)
I'm using another BLE...
Hi,
I was wondering if it is regual that configuring softdevice for a low frequency oscillator 32.768 kHz using the function:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi,
Here is output of my chip and i want to read it but there is a problem 25 uS low width (T) is to quick for nRF51822
Can you give me some tips, how to read this 3 signal...
Hello all,
I notice that this library isn't listed in the "SDK Common Libraries" for S210 - is it ok to use this? Internally it does seem to be ANT-aware, even though softdevice_handler_init...
Hi everyone,
I'm using NRF51822 controller for an application, to store 2 float variables in the memory using persistent storage manager feature.
However, when I try...
Hi All,
I try to implement the DFU funtion in my module, but the message return is “Not Supported”.
Please suggest me, how could I do about it?
Thanks.
Vic
...
Hello,
Is there a restriction that I cannot have same address LSByte for radio pipes?
It seems that i am failing to receive data on pipe 0 if for example I have pipe 0...
