Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hello,
I'd like to know how exactly do i implement this function in my app?
I tried getting the value from response (as shown in documentation) : ble_gattc_evt_char_val_by_uuid_read_rsp_t...
Hi,
My Jlink lite CortexM work with nrf51822 DK boards. But my PCB with nrf51822_xxAA chip can't download code. I'm using ukeil
When I chek in utilities Jlink can't recognize...
I am initializing an SPI master to talk to ADXL362 accelerometer using NRF51-DK.
Datasheet page 19: www.analog.com/.../ADXL362.pdf
No matter what I do connected or disconnected...
Hello,
I am new to working with imbedded chips and could use some help. I am working with a pre-programed nRF51822 chip on a PCB and would like to be able to read the imbedded...
Hi I want to using nRF51822 link with MCU ti-am335x have Linux system(Ubuntu) by standard HCI command, BlueZ or related hci tool.
I know that I can use nRF51822 S120 serialization...
I would like to share my wireshark capture file (pcapng) with another developer to view that doesn't have a nordic sniffer. They cannot see the ble protocol information. Is...
I am able to set the connection timeout to 250ms in the ble_app_hrs peripheral sample, but in the ble_app_multilink_peripheral it will not advertise if I set it below 1000ms...
Hello,
When using the bootloader I've noticed that the booatloder resets after advertising for ~1minute. I'm try to figure out if this is intentional.
I notice that...
Hello,
I am currently designing a project that will advertise as two different beacons simultaneously using the Timeslot API. I have successfully implemented the nRF51...
In my all projects, I am using this code to obtain and set local device address:
uint64_t deviceId = ((uint64_t)NRF_FICR->DEVICEID[1] << 32) | ((uint64_t)NRF_FICR->DEVICEID...
Hello,
I build a Broadcaster(iBeacon) with the DK PCA10028. This Broadcaster sends periodically ervery 30ms a message (I have sniffed the Broadcast message and it appears...
Hello,
I am having some strange results with some firmware I have been developing. I developed the firmware on the nRF51 Development Kit (PCA 10028) and the device advertises...
hi,
i would want to develop a project with master (mobile phone)- bridge (acting as master and slave,nrf board)- slave (nrf board) .
i have tried the ble central(s120...
