I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
Routine running normally in low power mode with power_manage() .
but after sd_flash_write/erase current consumption goes high(almost 20mA).
If anything is missing...
Hello,
i want to update the softdevice S310 V1.0.0 to version V2.0.1. My applicatio based on SDK 6.1. With S310 V1.0.0 all works fine. But i can't update to S310 V2.0.1...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hello, I have a problem with GPIO Input control
My sensor work on special clock generated by MCU
I've controlled this sensor by Arduino like this
//SCK digital pin...
We are using the NR51422 to develop a BLE application. We reused the project “ble_app_hrm” from the SDK v6 and ran it using the NRF6310 board, everything is ok.
We just...
Hello Everyone, right now i use nrf51-dev kit and i want blinky code for that, in Keil i compile code and load in kit and it work fine but now i want to make code in eclipse...
I'm trying to debug the blinky example with SDK 7.1 using Eclipse Luna. Going through several threads here I could figure out configurations needed and build the app. I can...
Hi,
I have been trying to study how to implement support for over-the-air (OTA) updates in my current S110-based project. But I'm already stuck in the very beginning. How...
I am using softdevice and RTX at the same time.
RTX is using RTC1, softdevice is using RTC0, so no problem there.
But sd_softdevice_enable require a clock source as one...
Hi,
I have problem with nRF51 antenna orientation. I used nRF51 developement kit (mKIT) board and I had problem with communication if I just change a little inorientation...
Can I change the shared channel address (first one or first two bytes in the message) when the channel is open?
The manual says after opening the channel, send a broadcast...
Hi,
I rely on twi_hw_master (from sdk 7.1.0) to communicate with a sensor. It works without any issues without the SoftDevice. With the SoftDevice enabled, using TWI causes...
Would you recommend purchasing Red Dear Lab Development Board? Or should I get an EVKIT from Nordic Semiconductors?
Nordic Semiconductor eval kits are expensive and shipping...
