I was doing development on the development kit and I noticed that when flashing the device there is application core and modem core firmware that is flashed
I'm trying to...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hello, as the title suggests, I have an issue when powering the nRF9151 DK with an external power supply. Normally, I power through USB, and it's fine. However, when I followed...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have to asked that i am working with custom board of nrf5340 and i want to flash and check the rf signal by flashing through the nrf5340 development board and i am...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
As an example of this routine：
D:\Project\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs\ble_app_hids_mouse_pca10040_s132...
DK is not powering ON suddenly.
All the Power Switches are selecting properly (SW8 = ON, nRF Power source = VDD, SW6 = nRF ONLY)
USB is connected to J2 Connector.
Observations...
Has anyone been able to connect the nRF52 to MATLAB using their new Bluetooth Low Energy Communication interface ( https://www.mathworks.com/help/matlab/bluetooth-low-energy...
Why is "No location data available" always printed when SUPL data is downloaded in gps sample app? This happens at any place. I guess this causes a long TTFF.
This is a...
Hello. I have a DK nRF9160 0.8.2 version. I am sending AT command through UART with an external MCU (STM). I am interested on evaluating power consumption during an UDP packet...
Hello,
I am trying to integrate OPTIGA Trust X with the OpenThread example, "mqttsn_sleepy_subscriber"(from nRF5_SDK_for_Thread_and_Zigbee_v4.1.0 SDK). I tried adding...
Hello.
I am running Segger studio 4.5 on Windows 10 and the ble_app_uart example project that works fine with one connected central device (i.e. iPhone with nRF Toolbox...
Dear all,
I'm using nrf52-DK with PCA10040 as sniffer. I develop 2 custom board (nRF52840) (one acting as master, one as slave) and I would like to make some considerations...
Hi,
I have develop an application using the nrf52832 combined wit the ICM20948 sensor.
The application use ESB communication between peripheral and central. I have solder...
Hi,
Keywords: nrf52832, pwm_driver, two pwms, 6 channels, pwm in sequence
I have four LEDs: three mono white LEDs, one RGB LEDs(three color leds) that produce white...
Hi,
I use usb_msc in nRF5_SDK_15.3.0_59ac345 use case, format file system and create folder and its subfolder test, found that segger development environment compiled programs...
Hi
I have followed the all the instructions with regards to 'nRF9160 DK Getting Started' and all is fine until the stage "Building and testing a sample application" where...
Hi Team,
We need to enable the two crypto backends one is CC310 and mbed TLS at a time for our development purpose.
Why means one of our features used 128 bit AES ECB...
Hi, I need a little help with understanding to implement security in my application.
Most examples used by Nordic have public advertising on, so any device can connect to...
