The firmware always halts execution during boot after providing these logs:
26/05/22 10:38:33.925 89737.861 13892 0 E: Device id 00 00 00 does not match config 1f 16 01...
Hi Team,
Whether there is any configuration or option available to disable/eliminate signature verification during the boot process.
If disabling is not recommended...
Hi,
I am using NCS v3.3.0 and would like to implement the following setup:
Central: nRF52840 Dongle (connected to PC via USB)
Peripheral: nRF52833 acting as...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hi support team,
In my case, i want to auto disconnect to ble central after some minutes with no message transfered, so i create an timmer and set event compare and clear...
We are developing a beacon with nrf52810. We test ble_app_beacon example and a modified example( the difference is, advertising packets are connectable to be applicable in...
I've configured UART2 on the nRF9160 to connect to a nRF52840. The nRF52840 generates a payload and sends it over to the nRF91. The payload size during testing was 65 bytes...
Hello,
I am developing using nrf2840 PDK, SDK v17.0.0, S140
I have made two services, one is to control the led blinking rate via nrf connect android app and the other...
Hi,
Is it possible to have dual transport for DFU (UART and OTA)?
I read this in the forum: https://devzone.nordicsemi.com/f/nordic-q-a/28118/multiple-dfu-transports ...
I have nRF52840 as the central and nRF52832 as the devices. I have the device names as TELCO_456, TELCO_457, TELCO_458 in the connectable advertisement packet. I have disabled...
I am trying to capture sniffer logs for a custom BLE peripheral using nRF51 dongle and Wireshark. I am following this guide here to install the Sniffer tool in Wireshark....
>I will start by prefacing that I'm not by any means an engineer and my only knowledge with BLE/embedded systems comes from curiosity, side projects and trial/error<
Story...
Hi,
I'm running of the fw-nrfconnect-nrf master branch (commit: 96e75dba598320c2707dede3ffef44bf326a89e3) because there are some improvements since the release of SDK v1...
Hi,
I am developing a custom device with nrf52840 and use SPI for flash driver and radar sensor.
For better SPI performance of the flash driver and radar sensor, I am...
As an example of this routine：
D:\Project\nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_hids_mouse\pca10040\s132\arm5_no_packs\ble_app_hids_mouse_pca10040_s132...
DK is not powering ON suddenly.
All the Power Switches are selecting properly (SW8 = ON, nRF Power source = VDD, SW6 = nRF ONLY)
USB is connected to J2 Connector.
Observations...
Has anyone been able to connect the nRF52 to MATLAB using their new Bluetooth Low Energy Communication interface ( https://www.mathworks.com/help/matlab/bluetooth-low-energy...
Why is "No location data available" always printed when SUPL data is downloaded in gps sample app? This happens at any place. I guess this causes a long TTFF.
This is a...
Hello. I have a DK nRF9160 0.8.2 version. I am sending AT command through UART with an external MCU (STM). I am interested on evaluating power consumption during an UDP packet...
