Hello
When I tried to learn the development of nrf54H20, I run some samples supplied in the SDK2.7.0.
Most of them works well.
But when i try the Bluetooth: Multiple...
Hi, I'm currently working on porting an nrf5340 - NCS 2.6.0 project repo to NCS 2.7.0 starting with my own minimal sample. Having some trouble getting the sample to build...
We have experienced some modem faults and have implemented a custom `nrf_modem_fault_handler` to try to capture them.
We have enabled the config:
CONFIG_NRF_MODEM_LIB_ON_FAULT_APPLICATION_SPECIFIC...
I am currently using the nRF9160 SLM firmware to send data over MQTT via datamode.
After connecting to the MQTT broker, I enter data mode using the following command: "AT#XMQTTPUB...
I'm trying to make a BLE beacon with Li-Ion battery and Qi wireless charging circuit. NRF52833 works in high-voltage mode (VDDH connected directly to the battery, internal...
I have mistakenly disabled Software Debugger (SWD) and wrote the configuration back to the board. Ever since board can not
(1) Connect and get the configuration data using...
Hello I want to add an extra config file based on the option in prj.conf or in Kconfg. For example: CONFIG_WIFI_SCAN_ONLY=y include the overlay-nrf7000-wifi-scan-only.conf...
I'm wondering if anyone uses unity.c for unit testing and managed to change the print function to segger rtt in order to read the output.
According to unity
By default...
Hi All
I am now working on Channel Selection Algorithms in nRF52840DK by Zephyr. For right now, the choice between Channel Selection Algorithm 1 and 2 could be made by me...
We have been using the same inductor that Nordic uses on the dev kit board, the Taiyo Yuden LBMF1608T100K. We are trying to make some new boards quickly and these are not...
Dear Nordic,
I met a problem while using nRF24L01+ about MAX_RT interrupt.
In my codes, I disabled RF HW retransmit (hal_nrf_set_auto_retr(0, RF_RETRANS_DELAY);) because...
Hello,
From the datasheet of nRF52840, I found the 32MHz crystal's package is 2016 (reference circuit).
Is it necessary? Can I use bigger package?
Thank you.
Hello, I am trying to create a clone of a temperature sensor with the nRF52840 DK. I catched all important data from the sensor to configure the nRF52840 DK. But I cant find...
Hello.
I am trying to implement a Zigbee Network were sensors will be posting data periodically to a Coordinator.
I was looking into the examples provided with the SDK...
Hi team,
Our customer use nRF52810 to be an RF dongle.
They meet an question was about the high PER when there was an headset dongle was near nRF52810 as bellowing....
Hi,
I had the issuse about power consumption of saadc.The current measured was always more than 500ua after I called nrfx_saadc_sample().My test code is below.
I am using nRF32 ble module. I am not able to get the value from BluetoothGattCharacteristic. I have declared an object of BluetoothGattCharacteristic and getting the value...
Hi everyone,
SDK version: 15.3.0
I read the DFU documentation and can't find the <InstallFolder>\examples\dfu\bootloader_secure_ble folder in SDK 15.0.3.
This folder...
Hi.
I have problem with dfu over ble with mesh sdk. I use example experimental_lpn as guide. When I add this dfu functionality in my project, my application is not responding...
We are designing a radio transmitter for a long range hobby craft vehicle with Gazell. We need to use frequency hopping as well as the pairing functionality that Gazell offers...
Hi,
I have few questions to be cleared before get into the nRF9160 to use in India.
As per the datasheet, nRF9160 supports LTE CAT M1 and NB1/NB2.
Can I be able to use...
For Above case i am planning to interface with U FL to SMA cable for external antenna interface. nrf9160 ant pin and U FL connector will be routed using 50 E impedance. at...
