Hi everybody. Recently, I've spent nRF Connect SDK Intermediate online course. I could add firmware upgrade ability using FOTA and now, I can update the firmware using nRF...
I'm working with custom boards using the nRF9161 chip. In the process of trying to test the layout of my custom board, I was able to successfully connect to and flash the...
My custom board with a NRF5340 (MDBT53-1M) with LF crystal is running as a central on NCS 2.6.1.
It's connecting to a legacy device which has a BLE121LR.
NRF5340 centrals...
I'm trying to run the vanilla HTTPS sample on the nRF9161 DK: sdk-nrf/samples/net/https_client/README.rst at 4b9841a28e97e9d61b93f8981375d644b9d04ea0 · nrfconnect/sdk-nrf...
Hello Nordic community,
I am currently working on developing applications for Matter over Thread and have set up my ZAP file accordingly. I've successfully flashed two types...
Hi，
I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully.
sdk: ncs2.8.0
project: direct_test_mode...
Hi,
We are designing a USB Receiver based off the Nordic Proprietary Radio + ESB.
Do you have any reference designs for a PCB antenna which must be as small as possible...
Hi
ZED requests beacon every time when it restarts both case ERASE_PERSISTENT_CONFIG is true or false.
But
ZR does not request beacon when ERASE_PERSISTENT_CONFIG is...
Hello,
I've been using the nRF52832 with a Segger JLink Pro which works fine during execution. However during the system initialisation, this is just before getting to the...
Hello,
I have used nRF24L01+ in one of my scientific paper. I need to provide a detailed reference as a citation in this paper. I couldn't find the documentation of nRF24L01...
Trying to have the Nordic Thingy advertise to the ESP32. Using example code found in the ESP32 BLE Arduino.
When running the program, BLE Client, we are able to see and...
hi all,
how to revert interface MCU ATSAM3U2CA-AU(J-link )
when i plug in usb port to PC, DK board can't active .(PC can't detecting any USB Emulators)
check list...
Hello, I am using nrfgo studio to flash softdevice, application and bootloader on nrf52832 I am getting below issue:
" This hex file has data in SoftDevice region. Try programming...
We are using v0.4.0 lte_ble_gateway example running on an nRF9160-DK (0.8.5)
We are successfully pushing data from the UART on the nRF52840 to the nRF9160
Also managed...
Hello, I'll buy ISP 4520 (based on nRF52832) kit.
I request information about the processor's 'power down' of the LORA / BLE combo module.
Depending on the wake-up method...
I am currently working on adding the ambient light sensor to the asset_tracker application firmware. I have managed to configure the I2C, configure the sensor and read the...
I am developing an application as a peripheral based on the NRF52 SoC which regularly reads a sensor and publishes the reading to a BLE characteristic. A central (a smartphone...
I'm building some of the samples using command line in Ubuntu and have a strange issue. Everything builds fine, the merged.hex file is generated, however when I try to flash...
Hello All,
Currently i am working on nrf51422 DK board(PCA10028). I am using SDK 12.3.0 ,from this i have referred the ble_app_uart example for implementing the UART and...
Hello,
After following the steps of the tutorial : https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with...
