I'm facing a persistent issue with my nRF9151-SMA-DK kit when trying to perform USB debugging, uploading, recovering, or erasing.
Interestingly, other boards (nRF9151-SMA...
Hi everyone,
I'm facing an issue where MCUboot doesn't perform a swap after reboot, even though the DFU download to slot 1 completes successfully and boot_request_upgrade...
I am getting the following build errors when working with both DFU (MCUboot) and the file system (FAT FS) together. Errors: D:/ncs/v2.9.0/zephyr/drivers/disk/flashdisk.c:533...
Hello,
We are working on an audio project where we are using nRF5340 Audio DK. We want to externally interface the digital microphones without using the on-board codec ...
Hi, We want to integrate LORA LR1110 for the final year capstone project. From the documentation we have understood that Kit is fully compactable with Arduino UNO. But SPI...
안녕하세요
nrf9160DK 보드로 개발하고 있습니다.
blink 예제로 컴파일 및 다운로드되었음을 확인했습니다.
SDK에서 예제AWS_IOT_MQTT로드하여 테스트하고 있지만 아래와 같은 오류가 발생합니다.
해결 방법을 가르쳐 주시면 감사하겠습니다.
zephyr/subsys/net/libsubsys__net...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
We wanted to implement both BLE and serial DFU on nRF52832 without serial flow control. The main procedure is as follows:
Use the Nordic BLE DFU example as a start...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
I have queries on enabling HW crpto accelerator...
I'm implementing the device side of the DFU-protocol (v16) (Control Point & Packet) using the nFR Connect Mobile as DFU Controller. In the app I select Application as file...
Hi All,
Since 2 weeks I try to configure a gap with a "raw payload" but it's a Chinese puzzle! Between different SDK, with different "Soft Devices" and examples dating back...
Hi,
I've install the throughput example (examples/ble_central_and_peripheral/experimental/ble_app_att_mtu_throughput) on an nRF52840-DK and I test it against all kind of...
I made 20 pieces of porototype devices. Testing some damaged them, NRF52832 does not work and the voltage on them is 1.556V, others work again but after disconnecting the...
Hello All,
I am trying to publish the data gathered from UART using MQTT . So far I was able to get serial data in the inData buffer. I am not able to publish data automatically...
To the kind attention of Nordic support team,
According to your valuable experience and manufacturers' capabilities, having the package a pitch of 0.35 mm is it possible...
I use nordic 52810.
I am trying to use s112 and HW IIC but I got the compiling error:
twi_hw_master.c:34:5: error: 'NRF_TWI1' undeclared (first use in this function) ...
I have a nRF52840 based product prototype which includes a power management integrated chip (PMIC) and a Li-Po battery.
The product recharges via a USB connector. The USB...
I am always getting the same issue on each sample I try to build. Not only on this "lte_lc.h". This error is also shown with several files or on the code lines....
Checking...