Hi
our last product is based on nRF5340 and now we start a new design based on nRF54H20, and its essential for our design, i checked alot but there is no datasheet, reference...
just passed Cellular IoT Fundamentals while I was waiting for my nrf9151dk to be delivered... Now that I have the DK I can't get the dk to be provisioned...
I couldn't get...
NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
I am using s132 v5.1.0 and am in the process of implementing an error-handling architecture.
I'm noticing that much of my error handling could be avoided if there were APIs...
I'm trying to get mcuboot to run on the nRF52840 on the nRF9160 board. I have been able to configure it and get the resulting merged.hex file loaded on the processor and it...
Hello ,
I am using a Laird's BL651 module that has a nRF52810 chipset. I have modified the ble_app_uart example to take a command from Rx characteristic and send a response...
I'm working on IEEE 802.15.4 network using nrf52840 DK boards. I'm making use of the examples in 802.15.4 (secure). I wanted to know how the reception between a transmitter...
I am using SDK v15.3 and modifying the ble_app_uart_c example to setup ble_nus connection between nRF DK board and a custom peripheral. I can use nRF Connect to send and receive...
Hello,
I am using nrf52832 with nrf Mesh DK. Is there a way to unprovision the board from the hardware or command line and not from the app?
Many thanks in advance , ...
Hello , I noticed that my NRF DK advertises for a few minutes and goes back to sleep , because of Advertising Timeout set (I am using the BLE Peripheral Example) , but when...
hello,
I am using SDK v15.2.0,s140,pca100056. In my custom application I am using 3 SPI, RTC, timers, USBD, etc.
Actually during the development stage I have used DEBUG...
Hello,
I am trying to understand the working of BLE Mesh network and have the following question.
Is it possible to make phone as Proxy as well as Provisioner? BLE...
We are planning to build a product based on nRF52811 SoC, which is Bluetooth 5.1 and has AOA and AOD features. Unfortunately, Nordic's hasn't released any new supporting Library...
Hello
my setup is a nrf52840, the sdk15.3, Softdevice s140.
I'm running an application with freertos and wdt and have the openbootloader and s140 also flashed.
- if...
Hi,
I have an application which has 2 services and 3 characteristics. I want to keep the value of characteristics when the characteristic value changed. I tried FDS and...
Hi everyone!
I have recently implemented USB CDC on a custom NRF52840 device with SDK 15.0 and got it to work with Windows, Mac, and Linux OS. However, when I try it on...
Hi Everyone,
I am using nRF52832 with SDK v14.2 and SD v5.0.0 on a custom chip.
I want to advertise 2 custom UUID (DFU and NUS) and i wanted to know the correct way to...
