Hi,Team,
I'm currently using the nrf54l15-dk. I want to set the rtc of the nrf54l15-dk to obtain the timestamp. How should I configure the rtc? Which examples should I refer...
Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
Hi,
I am trying to set up a project that continuously measures the pulse width of a signal that may or may not be present at a pin.
I want to use a Timer in capture...
I've been following the information on the nRF54H20 with interest as it is most likely the natural candidate for upgrading our existing design. However, I have been waiting...
We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
My setup is NRF52DK+SD132_V3.1.0+SDK_12.2.0.
While playing with my peripheral I setup a whitelist, the default whitelist filter policy seems to be BLE_GAP_ADV_FP_FILTER_CONNREQ...
Hello everyone,
I want to establish serial communication between 3 nRF52840 dongles using mesh.
Can you suggest me the steps from begining. Also i have read the documentation...
I'm using SDK version 15.0.0_a53641a on nRF52840 with softdevice s140_nrf52_6.1.0_softdevice.hex.
When I enter break points inside ble_evt_handler, it always ends up at...
Hello,
I am trying to get Keil to work to program my Custom PCB. I am using Keil uVision5 MDK-Lite Edition
SDK: nRF5_SDK_12.3.0_d7731ad
Device: MDBT40-256R V3 (nRF51822_AC...
I need to incorporate eMMC in my code.But heard that it is not compatible in nrf52. So I would like to know how to include eMMC code right from the beginning the algorithm...
Hi,
I was able to run hid mouse example on my laptop. But when I tried to do the same on my other laptop it failed to execute properly, although the bluetooth pairing was...
HELLO SIR
we are working on our current project on bluetooth , we are trying to broadcast message via one nrf52 DK to other nrf52 DKs . i tried implementing the uart example...
Dear Sir,
I am trying to use a whitelist on peripheral side so as to connect the peripheral to a given phone/App.
At first I enabled the "p_advertising->adv_params.scan_req_notification...
I am requesting a USB booloader hex file or if possible the complete project. I have been doing some hacks on mine and have erased the USB booloader. A quick search through...
We are working on the BLE Smart Switch. The requirements are pretty generic:
Low Power consumption
To be used by multiple smartphones within the house
The obvious...
Hi,
I want to set the TX power in a mesh proxy configuration. I have read mesh sdk2.1.1 TX power of nrf52832 , which works good for not proxy situation (e.g for light_switch_client...
Hi, I'm having troubles adding PWM in light_switch_proxy_server example in Mesh SDK v. 2.1.1.
It seems that the PWM driver and instances are not correctly enabled, looking...
Hello,
I was wondering if there are any article or tutorial I can follow to optimize code build with Segger Embedded Studio.
I was able to follow this article( https...
I need logging in almost anything I do, but I've never been able to start from an example that does not use logging and add logging. I've set the NRF_LOG_ENABLED and NRF_LOG_BACKEND_SERIAL_USES_UART...
