I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hi,
I’m working with the Wi-Fi station example on the nRF54H20 using SDK v3.0.0, and I’m encountering a critical issue when trying to bring up the nRF7002EK Wi-Fi module...
Hi Nordic team,
I'm trying to configure the GPIOs to operate at 3.3V using the nRF Connect for Desktop's Board Configurator tool (v0.3.10). The tool works as expected...
I am using 3 nrf52 DKs with S132 and SDK14 / and SDK15 to try and implement a combination of the multilink and UART examples. I started with the ble_app_uart_c example and...
Hi All,
We are working on nRF52810 chip for on of our beacon project and we are using external antenna on board but
We are dealing with the Reason 8 disconnections.
...
Hey Team,
Can anyone please share the layout of the Program and Debug connector on the Thingy? I don't have a 10 pin SWD connector readily available and need to start...
Hi everyone, I have configured the LOG module to use it with the UART in view of debugging. I don't send anything in my loop but the UART send constantly these data :
<info...
Hello,
I am using sdk12.2.2 and nrf52832 customised board. My use case is as follows.
Suppose user enters in dfu mode trough app and for example user doesn't update...
I am working with nRF5_SDK_14.2.0 ble_app_beacon example using NRF52 DK. If I have directly copy pated the readily available examples\ble_peripheral\ble_app_beacon\hex\ble_app_beacon_pca10040_s132...
Hello,
I am building an application that doesn't need high-frequency microphone data.
I want to sample the PDM at 4K. It is possible to do so by changing the frequency...
Hi,
After i merged the light switch example in mesh_v1.0,1 sdk with UART example in nRF5 _v14.2 sdk, i'm trying now to put the status data recieved from server node to UART...
Hi,
We develop two BLE projects on NRF51822 and NRF52832 chips.
In both chips, for higher accuracy (better than ±250ppm) exists the option to connect the LFXO 32kHz crystal...
Dear Nordic Engineer,
I am working on sdk15,52840,ble app uart project,
i saw BLE_DTM_ENABLED in sdk config.
// <q> BLE_DTM_ENABLED - ble_dtm - Module for testing RF...
after flashing the board couple of times I get the following error:
device recognized by PC, I can see the drive created on PC
however I can not flash the device, and...
I am developing an IoT Gateway having BLE chip nRF 52840. The BLE of the gateway will connect to and transfer data to a BLE device having Vendor Specific GATT service and...
Hi Nordic,
Any chance I could port Nordic Thingy AWS alexa example code(in js) to Nordic nrf52 dk code(c language), I cannot locate any working AWS example code for nrf52...
I'm having a problem merging the Mesh SDK v1.0.1 with nRF5 SDK 14.2 following the " Coexistence with other Nordic SDKs" section of the Mesh documentation. I have a fresh unzip...
