Hi all,
I'm modifying the Matter Light Bulb example from Nordic's nRF Connect SDK to integrate I2S audio output on the nRF5340 DK. The goal is to play a continuous beep...
Hi,
I'm using an nrfx_timer event with k_poll_signal_raise to trigger a thread to perform an operation.
I've noticed around 900ms delay between when the signal is raised...
I am using bumble( github.com/.../bumble) as host and nrf 5340 audio DK as controller. I use python auracast.py scan serial:/dev/ttyACM0,115200, and this error appears: Periodic...
I used the Bluetooth mesh distributor example from ncs2.9.1, and the Bluetooth mesh dfu can proceed normally. However, when I tried to pause and resume the dfu process, I...
I have a LIS2DW12 accelerometer connected to nrf52840 SPIM3, and I am seeing an intermittent failure. In some instances while collecting accel data during a data ready interrupt...
Hello,
I am looking to create my own custom NRF5340 AUDIO DK board. Could you point me to any NRF5340 modules that would be best to use with a pre-built antenna, available...
I'm running various example programs, and would like to find documentation for the functions I see them calling, for example nrf_drv_saadc_init...
Where can I find documentation...
Hi,
I have connected my custom pcb to the development kit at pin 19. When i use jlink commander, the board is detected properly. I use nrfjprog to dump the softdevice(Using...
I'm trying the get the development kit of the nRF52832 (PCA10040) displaying a floating point value. I read several postings of this problem, but non of the suggested solutions...
Hi, I'm having an I2C read lock-up issue similar to those described here , here , and here .
I'm using SES, SDK14.1, and an nRF52382. The only other component on the I2C...
Hi,
I have a custom board with nRF52832 SOC and temperature sensor in it.Interface Between the nRF52832 and Temperature sensor is I2C.i have to see the data through the...
Hello
We are currently making STN1170 based OBD II scanners with the nRF52810 for communications. The product is stable and available for commercial deployment, however...
Hello Supporter,
I'm going to develop one BLE nrf51822 based custom device. in which i want to use BLE DFU.
i am able to load DFU and APPLICATION with KEIL uvison 5. ...
Good morning, I have a question about MESH RF. We need connect many vehicles to station base via RF. - Station base --> UART --> RF Device [ MESH ] (SKY CLEAR and outdoor...
Hello Nordic community! My setup is pca10040, android tablet, s132, sdk14.2.
This time I am trying to understand why this code:
While using nrf toolbox nrf UART prints...
Dear All,
I would like to explore the possibility of repetitively transferring small amount of sensor data from an nRF52832 to an ANT(+) compatible Android device, for a...
We are using an MDBT42V(29 pin) module which we discovered from the datasheet, comes with an nRF52832 controller. We are using a nRF52 DK to dump codes into this target board...
I am using nRF Connect (PC version) a lot to debug my application. I am using a PCA10040 board as dongle and everything works fine most of the time. But after I keep the nRF...
SDK 14.2 libraries/util/sdk_errors.h includes sdk_config.h but does not use it. In other words, it falsely expresses a dependency.
This makes it harder to compile code ...
I'm trying to send a string of 140 characters length using UART.....but only 98 characters length is being recieved in the output.
what could be the issue? How many bytes...
I am using nrf52 with SDK 14.2.0 and SD is S132.
The issue I am facing is that after Central is paired with one peripheral and bonding is done, the bonding information...
