hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
We need to set a GPIO pin in MCUBoot to activate an external USB hub chip so the USB DFU will work. I would like to do this with code in our project rather than directly modifying...
Hello,
I’m working on a Zephyr-based application using the nRF5340 where I need to optimize power consumption. The intended behavior is:
The device should stay in...
According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
I have a custom dongle that connects to the PC through a USB-UART chip. It is based on the nRF51822. I have another board based on the nRF52832. This board needs to be able...
Hi,
I am building a device to act as an iBeacon, with other services layered on top. This is based on a Raspberry Pi with a Class 1 USB Bluetooth dongle.
I need to be...
Hi everyone, I'm working on the nrf51822 QFAAH I tried to flash the ble_app_uart example and it didn't work. So I debug it and it stops here
As you can see in the picture...
I am working on app_uart and buttonless_dfu. Although i am getting certain errors which i am unable to counter.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
I have 32x64 RGB LED Matrix, and I want to use nrf52 to control it. I got the driver working and I can display everything. It is a time interrupt driven driver, just redraws...
So I just got my nRF52_DK, got everything installed and compiled an uploaded the blinky example. Fine. I had my custom PCB ready, and got the 52832 soldered in straight away...
Hi, I am a newbie to embedded development. I am well versed with java script. I am under the impression nordic allows you to communicate with java script to the development...
Hi, we're using \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hids_keyboard to test Pairing/Bonding/whitelist.
After connection, when the central try to read...
Hello,
We have constructed a custom board of nRF52832 via I2C communication with sensor and INT based wake up. Following configuration enable
DCDC Power Enable
Disconnected...
When I was using a master slave integrated host, when I quickly disconnected the connection and then set up the connection immediately, it was found that the original disconnected...
Hello,
is there a simple example for reading out a value? The nRF5 is in this case a BLE peripheral server. The central device should only read one value at a certain time...
Hi:
I output a PWM channel in 16kHZ,i found that when i set the duty cycles 50%,my tft screen(i2c) display at a very slow speed,and it will be OK when i set duty cycles...
Hi,
I am trying to add a notification charactersitics on client, I am able to add one of them, but when i try to add another one sd_ble_gattc_write(), result is always NRF_ERROR_BUSY...
I am trying to use my nRF51 Dongle (pca10031) as a central.
I downloaded the nRF5_SDK_12.3.0_d7731ad and I could see that there is no BLE project for pca10031 (only pca10028...
i used nRF5_SDK_14.1.0_1dda907.
ANT protocol :
I used ant_background_scanning example.
I want to scannig device ID of hrm, bpwrt and bsc.
Then choose the device ID...
