Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have a USB HID device using the 'old' USB stack in Zephyr. I have configured the 'CONFIG_USB_DEVICE_REMOTE_WAKEUP'
1. I put the HOST to Suspend
2. The NRF52 USB goes...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
hello sir,
i am using ble mpu example and it working fine now i want do send some commands from mobile to nrf52832 chip via these commands my application should work.
...
Hi everybody,
I will to use the nRF52832 QFAA for a drone, and I carried out this schematic for this chip.
I have two questions :
For the capacitor C6, which value should...
I'm trying to start my app from the bootloader, which is funcionally basically the same as the one in nRF5_SDK_11.0.0_89a8197.
To start the app I call bootloader_app_start...
Hello.
I use nRF52832 and its dev board, S132 soft device. nRF5 SDK v14.2.0 is the version number.
I want to change some manufacture specific data from mobile app. Like...
I am working on the nrf52840 kit with the ble_app_beacon example, compile and download the code successfully. But I don't know how to test whether the kit is advertising,...
I have my own hardware design with the nRF52840 on it. I more or less copied the whole radio/antenna part from the dev kit reference design. The blinky example works fine...
After checking and searching, i found this ble_gatts_conn_cfg_t::hvn_tx_queue_size should be the key to set it. In my custom project (SD132 V5 + SDK14.1) the only setting...
Hi
I'm using IAR Compiler and need to generate some PWM outputs. I tried to use the example code from the pwm_library. But the compiler is generating an Error on the macro...
I am using PCA 10040 development boards with soft device version s132_nrf52_3.0.0 to investigate Central/Peripheral communications.
A PCA 10040 acts as a Central making...
Here is calibration of UART data using ADXL345.
and the data is followed by x, y & z value, for example x = -42, y = 20, z = 268. and then after calibrated 10x which is...
We are upgrading an existing product to use Bluetooth instead of the parallel port.
It must support >20kbit/sec communications between the device and the host PC.
We...
Hey Nordic devzone,
I am tinkering with the following multiprotocol examples:
ble_thread_dyn_mtd_coap_cli (client)
ble_thread_dyn_template (server)
Currently the client...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to connect nRF52832 in some android smart device.When I restart Bluetooth,Sometimes there are problems...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to scan nRF52832 in android smart device.When i disconnect the device a long time when the status is...
