Hi, I am currently trying to get through the NRF connect SDK fundamentals, I am on lesson 3 example 1, creating an application. The problem I am running into is that I cannot...
Background - We are laying out a new board, upgrading to the nRF54, and wanted to use p2.02 and p2.03 as serial UART lines because p1.04 and p1.05 were planned to be used...
Hello,
I face a problem which I can't understand really and where I need support.
It is strange...
In our electronics we use the nRF52840 which is enclosed in a module...
Hi there,
I have recently upgraded my software to latest ncs 3.2.0. I have noticed that my initialisation does complete but it ends up with fatal error that seems to be...
Dear Nordic,
I am debugging a custom hardware with a nRF7002 on-board, using wifi shell app. At this moment the shell does not work as expected, needs to locate where the...
I am attempting to install nRF Connect SDK along with VS Code on an offline machine for development. The main two issues I have are:
The NRF Connect for VS Code plugin...
Hi
I am using the nRF54L15 DK and build a thread continueing monitor the data rate in 1 Hz, if it is lower to 800kbps I want to change to 1M; while above 800kbps I want...
Hi,
I got an err_code = 0x00000007 after calling this function.
void system_timer_start(void)
{
uint32_t err_code;
err_code = app_timer_start(m_one_ms_timer_id...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
I set up a 2 GPIOTE interupts like this:
in main.c:
APP_GPIOTE_INIT(3);
err_code = app_gpiote_user_register(&mainUser, 0x00000000, (1 << RF_GPIO2), powerButtonInt...
Hi
I am using sd_ble_gattc_primary_services_discover(conn_handle,0x0001,NULL) to discover primary services on a GATT server. After the first call to this function, I get...
In nRF51 PS, I read typical/max time for AES ECB are respectively 8.5 and 17µs.
What would be those values for the whole AES-CCM operation (ie including MIC computation)...
Hello,
I'm working on a software we've made starting from the "ble_app_uart_s132_pca10040.uvprojx" source code. My "main" (procedure fct) is in the for (;;) of the void...
Hi,
A couple new fixes in listed files to supress gcc errors when -flto enabled.
hardfault_handler_gcc.c
port.c
Patches are in answer below.
Regards,...
I´ve read that the command "lib_aci_close_remote_pipe" is not available on the chip NRF8001 build code C. I need execute this command to solve a bug in the ANCS service. If...
Hi
I have setup and configured Eclipse using the tutorial and all seems to be good, except, I cant flash the binary to the chip. Here is my error when calling flash:
...
Hi folks,
I'm trying to write a program to check out a pair of nRF24L01p modules talking to each other, and I'm a bit confused about two aspects of initialisation:
...
We are using your nRF24l01+ chip in one of our products. we are using 1 nRF as receiver and 5 nRF's as transmitters.
While trying to use the chip with multiciever configuration...
Using SDK13 - I would like to use the fds/fstorage libraries, but I'm told that "The experimental label is due to lacking test coverage for the two modules". here
At the...
Hi,
I've been suffering with detection of writing to cccd to enable notifications. The S132 (nRF5_SDK_13.0.0_04a0bfd + s132_nrf52_4.0.2_softdevice) never fires BLE_GATTS_EVT_WRITE...
