The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
In the LTE_MODE_PREFERENCE Kconfig description the CONFIG_LTE_MODE_PREFERENCE_LTE_M_PLMN_PRIO option states that: " LTE-M, PLMN prioritized
LTE-M is preferred, but PLMN...
Hi Team,
We require the detailed procedure for locking and unlocking JTAG access on the nRF54L15 device . Specifically, we are looking for:
Steps to enable JTAG...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
i am in very strange problem and was unable to debug it
i am using following code to write 16 bytes data to flash memory, my app hangs after executing custom_flash_write...
Hi all,
i'm trying to use the function of power warning with s132 and nrf52 with sdk 11.
i use the function
err_code = sd_power_pof_threshold_set( NRF_POWER_THRESHOLD_V27...
I am running example: nrf5-ble-tutorial-advertising on a nRF52-DK.
with SDK 11 and s132_nrf52_2.0.0 softdevice.
When I flash the code to the nRF52-DK, LED1, LED2, LED3 and...
Hello,
I'm using Ceedling, Unity + CMock to implement unit tests but I'm running into issues when it comes to mocking nrf_drv_gpiote.h.
I'm trying to test a file, call...
Hi Nordic Engineer, I refer to your previous post title "Running micro-ESB concurrently with BLE" and gonna to use it on our project.
I test it on 4 pcs of DK board, found...
I have a problem using ble_advertising_restart_without_whitelist(). According to the documentation (as I understood) it should start advertising without whitelist even if...
Hi all
When i am reading ANCS code, i have some questions. SDK 12
Question 1: when ble device are connected with ios, the pairing is wrong, how to handle validation...
I am attempting to port a custom ble service from sdk12 to sdk 14 and am a bit confused as to how to increase my uuid count. In sdk12 I did it like this:
uint32_t err_code;...
Hi
I am using wireshark 2.0.1(64 bit).When i am trying to capture the ble packets it showing error.I have attached the Wireshark error message.BLE Sniffer version 1.0.1.I...
In the Bluetooth Light Controller example for the client in main.c these constants are defined:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
Why...
Hi Nordic,
Sorry if I missed and repeated a question, just point me to the previous answer if it has been posted before.
I am trying the DFU example found in the SDK...
Hello,
I'm wondering that it is ok to route ANT line through board-to-board connector to chip antenna.
Because there is no space to place nRF52832 and chip antenna together...
Hi,
I've seen that SDK 12.3.0 contains a new version of the application sample using the Eddystone protocol for BLE. I would like to know if this version is compatible...
I am using the template example for S130(works fine).
I tried adding a simple Pin interrupt on the code but it didn't call the pin interrupt handler everytime I press the...
