I am trying to run the debugger from the nrfconnect extention for viual studio code. for some reason It doesnt work, It seems to flash the app fine, but then this message...
Hi,
I believe the default application on Thingy91x uses LTE-m to connect, which is working fine. How do we make it use only nB-IoT?
For Thingy91, there is a guide
Getting...
I am using 2 nRF528400DK boards. Each board has a unique BLE Mesh sample loaded. The samples were made by modifying the default mesh sample provided by zephyr. One sample...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hi,
I'm working on nRF51822 with SDK 11.0.0 softdevice s130
I have an nRF module acting as central and smartphones (iOS and Android) acting as peripheral.
I tested...
Hello, what is the BLE max range w/out usin PCB antenna?
And what range ll be if i reducing the connection interval down to the minimum 7.5ms, set Tx power to +4dBm using...
I am using the nrf51822-QFAC-R in an application where the realization of the antenna is very challenging, and I expect to have an antenna |S11|=-1dB, with variations of the...
Hello, I want to clear things up a bit, all these concepts are starting to overwhelm me somehow. I want to know:
What can have UUID and handle? I understand that profiles...
I want to use ATMEGA 328 to send a packet over to the chip as follows:
SPDR = packet ;
Can some one kindly post what the content of this packat should be ?
is it possible...
hi,
i am working on FDS. here i am able to write number of records and also able to read them back.
but while updating i deleted one of the old record and writing new...
Hello,
I have some problems with UART communication with my nRF51 DK.
When I connect it through USB cable, all is ok. But when I connect pins: P0.09(TXD), P0.11(RXD) to...
Hello, i have a question.
Can nRF51822(s120) handle more than one connection at same time?
Let me explain: i have one server(nRF51), and two(or more) clients(nRF51 and mobile...
I've got an application that does a lot of nRF51822 GPIO wiggling and the timing needs to be controlled. In one spot I simply set a pin high then low like this:
nrf_gpio_cfg_output...
As shown in title, I am using the ubuntu 14.04 in virtualbox.
When I connect the Nordic 51822 development kit to my PC, I can only detect the serial number of this device...
keil uvision
Hello. I don't know how to get away from the warning "last line of file ends without a newline".
I added new line, but nothing change. It happened with my own...
Dear Sir,
Here I would like to disable the Adversting idle power down dynamically but in some situation it will fail.
The APP_ADV_TIMEOUT_IN_SECONDS is 180 seconds as...
I implemented a custom Bluetooth service on the nrf52_sdk similar the BLE LED project in the mbed site however when I copy the hex file and look at the debug output at the...
I am trying to setup a couple systems to use the Nordic rf sniffer. I have a pca10000, a pca10001 ver 2.0, a pca10001 ver 2.1 and a pca10031.
I loaded all with the rf sniffer...
Hello,
I am sending below setup packet to nRF8001, and i don't get any response form nRF8001. ACI as such works fine, i tried sending diff commands and able to receive...
