Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Dear Nordic, I'm using TIMER21 for our library, but I encounter problems with CC channels 6 and 7: their compare events never fire. The problem I configure the timer to generate...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi,
I'm trying to use sd_ble_gattc_characteristics_discover to figure out which characteristics are in a service.
On the whole it seems pretty obvious (keep calling...
I'm using the nRF52 + SDK11.0.0 + s132 and the ble_hrs example. The function conn_params_init() is called to initialize the connection parameters that the peripheral will...
Is there a way to pause all peripherals when hitting a breakpoint? In particular, I would like to freeze the RTCs when I hit a breakpoint. My app wakes up once a second, and...
I`m trying to operate PWM and soft device at the same time.
I have to make 4 Mhz using PWM block so I checked the PWM driver. There is no problem when using peripheral/pwmdriver...
Hello there.
I´m using a Taiyo Yuden evaluation board with a nRF51422 to connect with 3 different sensors. In addition to that there are also 2 buttons connected to the...
I am working on a BLE peripheral. I have a large, variable length characteristic I need to set from the central.
When the central is the BTool, I can write up to the maximum...
I'm using the nRF52 + SDK11.0.0 + s132. I started with the ble_hrs example and modified it. I now want to make the service/characteristics use proprietary UUIDs and I'm following...
I have been having issues with bootloader launching my application on a custom nRF52832 based hardware device.
The bootloader itself seems to be successfully completing...
When designing the layout for my circuit using nRF52832 I've noticed that the values of CL connected to the ANT pin changed from L= 3.9nH and C=0.8pF to L=3.3nH and C=1pF...
Hello, I'm trying to generate DFU keys with the nrfutil.exe tool from Master Control Panel 3.10.0.
I always get errors....
C:\Program Files (x86)\Nordic Semiconductor...
Hi,
nrf51822 device obverse six bytes mac addres could change，when OTA failed.
six bytes mac address, five bytes fixed, one byte can change when OTA failed.
Now，my app...
Hello,
I am using Nordic Nur-10W develop kit, trying to compile NurApiExample in Raspberry Pi. I wrote a Makefile, and complie process was OK. However, undefined reference...
hi
im using sdk v6 and when i turn my board on it goes to bootloader and i can upload my program into it .
the problem is that i want it to run to my main program after...
Hello,
I would like to use a custom flash memory layout for the flash memory of nrf52:
I thought that I should be able to use the UICR.NRFFW[0] - if I set to the start...
