Hi,
I was looking at integrating a speaker in my design and i have a class d amplifier that takes in an analog signal which i want to feed directly from the chip. I wondered...
Hello,
I am using SDK v2.9.1 for a Bl653 (NRF52833) and was trying to use the Nordic Academy Example for how to setup the SPI bus. The Nordic Academy example states we must...
I'm currently working on configuring the nPM1300 used in our custom board. In the product spec v1.2, it supports 2 USB compliant current limits, IBUS at 100mA and IBUS at...
Hi,
I am currently trying to enable the GPIO output interrupt functionality on my nPM1300ek with an STM32. However, I am unable to get it work correctly(I was only able...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello, I am working on incorporating flash logging into an application that has a GRTC-driven EGU interrupt (capture/compare event). Here is where I am setting up the EGU...
We are experiencing some ESB link failures on the receiver end of our system: nrf54L15. After minutes to hours of use the receiver will stop getting data (we know the transmitter...
Hi all
I'm struggling with the easyDMA UART of nrf52. I've got a preview nrf52-DK here where I wanted to make a simple example with the following code but I never reach...
I'm doing a custom board with a nRF51822 FAAG0. I have in it the ST BAL-NRF01D3, with a 0.8pF capacitor.
In the forum I read in a post that some versions of the nRF51822...
Hi everyone,
I am using the nRF51 SDK 10.0.
The documentation for the Debug Logger API suggests sample code like:
uint32_t retval; // Initialize module
retval = app_trace_init...
I want to use the J-link to program the nRF51822 via SWDIO and SWDCLK, every time I click the
"nrf51 programming", the studio stops working immediately, PLZ help, thans
I'm trying to set up communication between an nrf51422, and an nrf24l01+.
The nrf51 is supposed to be the PTX device, and the nrf24 the PRX device.
Communication from PRX...
I was learning GPIOTE using the example provided in SDK 9.0.0. (examples\peripheral\gpiote). The example only uses GPIOTE task and a timer to drive the task through PPI. ...
We have created a firmware and encrypted it with a private key and made it public. When we download it to the chip it's decrypted with a public key stored in the chip. Right...
I have about 200-300 sensors, each requiring to send data at around 0.5-1Kbps to a central node (coordinator/master node), what will be the network configuration/topology...
In SDK 8 for the nrf51422, notifications are always being sent as 20 bytes, regardless of p_len. The BLE_EVT_TX_COMPLETE event stores the proper number in tx_length, but the...
Hi everybody.
I am making an application which combine ANCS and UART on PC100028 (nrf51 SDK 9.0.0). This program worked properly. However when I add DFU service (dfu_dual_bank...
I am currently using Nordic's UART code and wish to build to use the UARTE rather than the legacy UART. I am currently using the following definitions in nrf_drv_config.h...
I use the S110 V7.3.0
I use the uart function ,I can use the uart function is OK.
But ,I need save power.
How can I turn off the uart function,while I was start the uart...
Hi,
When trying to update an application using nRF Toolbox on iPad, I get the error as in
this thread .
Turning Bluetooth OFF and ON does not help. On Android it works...
