Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
For nrf51, the current consumption is more than 1mA when GPIOTE is used since 16MHz clock is always on. Is this fixed for nrf52? or nrf52 still has the same level current...
Migration document is great - I'd be lost without it. I'm just trying to be sure I understand the two changes for "GATT Server Authorizable Write Commands" and "GATT Server...
Hi,
My S130 based BLE implementation, when scanning, seems to receive BLE advertisements out of order, when the traffic is high. I wonder why. Could it be so that the callback...
Hi,
I would like to misuse the SDK by creating an communications systems based on advertising. From several Q&A posts, e.g. this one ), I understand that the current S130...
Hi,
I am writing an application on top of NRF51, using a S130 Softdevice. I wonder about the concurrenceness (?) of the code I write, and especially if I need to use critical...
How do I make sure, the GATT server running on the BLE peripheral client connects only to a specific app based central/GATT client app, which has been authenticated via web...
Hi everybody!
I am working on ANCS and I found a problem that: At the first time I connect my Iphone to the dev kit, the pair request appeared on the Iphone. If I ignore...
Hi,
I have been having a lot of problems communicating with an Atmel SAM D09 as a slave, and an nrf51422 as a master.
I seem to have two problems, hopefully solving...
Hi all,
I design the kb based on the SDK6.1 and SD7.1 with 51822, and doing the PTS certification now, but meet some problem on TC_CON_BV_01_C, ATT Write error, such as...
the error messages show following:
compiling system_nrf52.c...
RTE\Device\nRF52832_xxAA\system_nrf52.c(92): error: #136: struct "" has no field "A0"
RF_TEMP->A0 = NRF_FICR...
Hi guys, I use old project try to build again in Keil when I installed nRF51_SDK_8.0.0. But I get the:
.\Objects\ble_knob_detection.axf:
Error: L6200E: Symbol
GPIOTE_IRQHandler...
Hi guys,
Has anyone encountered following warning message when using nRF51 SDK v8.1.0 or 9.0.0 and compiling project by GCC arm-none-eabi (I'm on V4.9 2015q2 which is the...
