Hello,
I have 2 Memfault projects that I'd like to rename, but I can't find any way to do this through the web app, and the API authorization keeps getting rejected (tried...
Hello, I'm working on a prototype device based on the nRF9151 DK.
HW: nRF9151 DK, nRF9151 LACA A1A Tested with modem_shell sample app, NCS v3.4.0.
Symptom: on boot, "The...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic Support,
I am facing an issue where the peripheral registers are not visible in the Keil debugger during a debug session. Only the core registers are available...
Hi:
Use nRF54LM20A_DK.
Use ncs 3.1.1.
And this is source code:
The following error occurred:
« *** Booting nRF Connect SDK v3.1.1-e2a97fe2578a *** *** Using Zephyr...
Hello, I use the NCS v3.3.0 (ncs\v3.3.0\nrf\applications\nrf_desktop). Can the desktop dongle connect to two keyboards at the same time? Development boards: two nrf54lm20...
With SDK 3.3.1 I do not get the <inf> logging messages when building the Hello World app unless CONFIG_LOG=y is added to prj.conf.
Perhaps this is left as an exercise for...
Hi,
we are now using nRF Toolbox -> Logger tool on our phone to monitor Thingy91 application information via UART/BLE.
Now we would to monitor/log the same information...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I manage to connect to the network and disconnect from it after sending the data, but if I'm in an area without reception, the device tries to connect and after a while, the...
: Chip Not Recognized by J-Link
I need advice from someone familiar with the nRF9160-SICA-B1A-R7.
I purchased an nRF9160-SICA-B1A-R7 chip individually from Digi-Key and...
Dear Sir :
We are now developing on nrf52840, with ncs v2.6.1 and zephyr.
We want to put I2C0 to PM_DEVICE_ACTION_SUSPEND before sys_poweroff().
Our code is below :...
Hello everyone,
I am currently trying to get a ML model running on my nRF52 (preferred nRF52832 but nRF52DK works also for me). Right now I am trying to evaluate if my setup...
We have using nrf5340-nrf7002 in our custom board. SDK version 2.6.1 We understand that the timer will not function in System OFF (deep sleep) mode. However, our project is...
Hi there,
I've encountered a strange PWM behavior and have investigated a bit. When setting load_mode to NRF_PWM_LOAD_WAVE_FORM, creating two sequence, and the latter sequence...
Hello, We want to build our own custom protocol because the features we need are not available from existing protocols like BLE or Zigbee etc. But it is beyond our reach to...
Hi all,
In my application I need to use some of the NET core peripheral from the APP core (since I ran out of peripheral instances in the APP core). According to this page...
I am running into an issue (title), where I am attempting to switch the advertising interval to a slower interval after a set period of advertising in order to save power...
Hello everyone,
I'm trying to test the ble_app_uart example. When I download the code into the 52DK, i can see my device show up as a possible connection, but when i connect...
We have a number of fixtures using nRF52 DK boards to both flash a custom board and to do a DFU operation to that board. We use a SPST switch in the P19 pin 1 lead in the...
Good day
Our custom board contains RS485 implementation. The file schematic for that looks like this:
I have noticed that a driver and sample exists but the driver doesn...
Hello everyone, I'm currently updating my project from SDK v10 with softdevice S110 to SDK v17.1 with softdevice S132 (a huge step). I'm, wondering if what I want my code...
