Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi,
I have seen this post , but it is quite old, so I would like to know what is the current solution to
update advertising packets while advertising, without stop and...
Hi there. I am freshman with the NRF MESH. I am working on project which I need to use the static provisioner node. The problem I am facing is how to configure multiple group...
Hi everyone.
I want to stream 12kB of ADC data from the thingy 52 via BLE. At the moment this takes around 4 seconds to do which is to slow so i would like to increase...
hi ,when develop the usb + gzll+ble hid funcation, i find that it will occur a erro when stop the ble stack in the project that have usb funcation,so i try in the project...
Hi,
I'm trying to debug CLI example contained into nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b by flashing it on my nRF52840 DK (PCA10056).
First of all I'm using...
Hello DevZone,
Currently I'm working to get the NFC examples up and running.
I'm using the PCA10040 in combination with SDK15.0.0 and SD 132
A colleague of mine mentioned...
Hi everyone,
I suppose this is a very simple question... I want to create multiple timers using the Timer Library .
Each time I want to create a new timer based on RTC1...
Hello,
I'm flashing custom code onto a nRF52840 based PCB.
I'm using SDK v15.0, SES 4.52.
On the debug window I get the following message as soon as I run the code...
Hi,
I am using nRF52840, S140 V7.0.1.
I am using Secure Serial Bootloader and able to do DFU of Application.
DFU of application
Using below command able to generate...
Hi,
I have a custom board with nrf52833 I would like to flash with custom firmware. I would like to flash this board by "P19 debug out connector" from DK.
How can I...
I am trying to port a tested program from NRF52 DK to NRF Thingy. To do the same I had changed the board to PCA20020. After I do that, I program using the NRF52 debug out...
Hi,
If the app keeps sending data at a certain rate, the numbers will skip and the software will stop.
I tried to see how much data I could communicate and at what speed...
In my situation, I want to use ble to designed a piconet which has 1 master and up to 4 slave .( upload(Slave->Master) rate is 2.2KB/s,download(Master->Slave) rate is 500...
Hi
A few questions regarding the "saadc_pca10040" example:
If I read one analog pin then what is the meaning of this matrix of values :
"static nrf_saadc_value_t...
