Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello!
We have nRF52832 chip on our product and we have some problem with one of its IOs.. We configured P0.16 as RX of UART, And when we run it we see this behavior of...
my example project: wireless_uart_raw_first_pca10056
chip : nrf52840.
i want to make my application timer in the my example project. time tick is 100 msec. in every 100...
Is it possible to get the Build Type from the Factory information configuration registers (FICR)?
From https://infocenter.nordicsemi.com/topic/comp_matrix_nrf52832/COMP...
Hi
I have some question about OTA .
1.The nRF SDK hvae twos way for OTA: single bank and dual bank;The nRF Mesh 3.10 too?Because my firmware maybe very large,so I want...
Dear all,
I am having issues with service discovery of two primary services ( Battery and one propriotary based on NUS) I am currently using SDK 14.2 on NRF52832 chip running...
Hi, I'm trying to use the Seggar Embedded Studio to debug my code, but the Seggar Embedded Studio can only recognize the nRF52840 development board, not the external device...
Hi,
On my previous question https://devzone.nordicsemi.com/f/nordic-q-a/47762/certification-when-bt-off ,
I got the answer about certification.
And now, I want to...
If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
I am using the Power Profiler app that is part of nRF Connect. This app was working just fine, but this morning I did the upgrade to v.2.7.0. Now, I am unable to control the...
Hi, guys. I copied the EAGLE schematic and PCB drawing file from the SparkFun nRF52832 Breakout design for my custom PCB (4 layers, FR-4).
https://cdn.sparkfun.com/assets...
We want to control the BLE Mesh network from the linux. As we understand the only one way to do it now - pyACI https://infocenter.nordicsemi.com/topic/com.nordic.infocenter...
Hi all,
We develop a custom board using MCU nRF52840(Master) and Module nRF9160(Slave).
I confuse to select an available circuit configuration from the reference circuitry...
Myself and others have received this error message
while upgrading nRf Connect for Desktop.
Despite the error message, the installer seems to have completed correctly...
I'm using an NRF52840 custom board along with FreeRTOS and soft-device S140 V6.0.
I want to access the complete 256KB of RAM for verification of RAM using a custom protocol...
Hi I'm considering a design with this precision RTC
I intend to use the 32KHz output on XL1 (and XL2 grounded) as I've seen done here, but the DS3231 datasheet says the...
