I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am working with nRFx modules and have a few questions about updating parameters. I started my project with an example and modified what I needed. However, I am not sure...
Hello Nordic experts,
I am trying to add an output endpoint to the usbd_hid_generic example in nRF5_SDK_15.0.0_a53641a. I exactly followed the suggestions in
https://devzone...
Hi,
I am using nrf52840 preview DK as a transmitter and try to get rssi by a linux lib. and it works well. and now I want to find advertisement channel number, because the...
I try to integrate Mult-touch(touch screen) and Keyboard feature in a single program, when I run this program, the phone side(Android8.0 based) can only receive Mult-touch...
When using nRF connect for desktop on ubuntu I can't go through the "Select serial port" step because I got the following error message:
"Could not open the port. Please...
With the release of SDK 15 has come the new nrfx module API's which seem to be easy to port to. One thing I have seen in the nrfx templates is the use of the nrfx_config.h...
Hi,
We are using nrf52832 micro controller and our device is consuming about 14mA current right now.so i have 2 querries that
1. How can we put our nrf into low power...
Hello,
I encountered an interesting issue with SPI0 on the nrf52840 that I cannot explain. In short, my SPI bus would stop working shortly after communicating with my slave...
Dear Nordic Semi, I play with NRF24L01+ shield and, what I control using STM32F411RE or ADuCM4050. Once a while, NRF24L01+ chip stops and on the MISO line with permanent 0xFF...
Hello,
I have been working with the example ble_app_hids_mouse to learn a bit whitelist. My code now doesn´t have anything about the mouse anymore since i only care about...
Dear Sir / Madam,
My customer is asking me if nRF51822 is compiled to the requirements of China's RoHS 2.0. Below are the requirements for tour reference.
China RoHS 2...
Hi
Can you please provide an example/pseudo-code on how the channel_mask member in the ble_gap_adv_params_t struct is used? The only examples provided in the SDK and the...
I have open a brand new nRF52 Development Kit. It is not recognise by the nRFgo Studio. I have tried the trick you mention on this thread:
https://devzone.nordicsemi.com...
