Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I'm porting the nRF8001 SDK to STM32 using HAL (CubeMX). Communication seems to run fine, however, the setup stops with CRC error. See abridged the logical output...
Hello everyone.
I am developing with nRF 52832.
However, when I call UART_init() function. my source code outputs an error message.
source code is under the line...
Hello, i'm using a nRF52840 on a PCA10056 and want to wake up from __WFE() with a minimum delay. When i'm using the debugger, i achieve a low latency but without the debugger...
Hello All,
We are working with one of the customer, where he is asking for range 200 meters between 2 nrf52Dk(nrf52832) and he want us to prove the same using two development...
I am trying to use the cryptocell in the bootloader (bootloader_secure_ble) for verifying dfu packages, but fails in signature verification for the same dfu package, same...
Hello,
I am designing the NRF52832 based board.Specifications of capacitor in reference design is as follows:
0.8pF, NPO, 5% tolerance
But with my vendor these two capacitors...
I am designing nrf52832 based board. In matching, 3.9 nH inductor is given.
I have selected the componenet with following specifications :
Specifications of inductor...
Hi Everyone
I am using nrf52832 development kit , sdk 14.0.0 with iar and i am trying to merge the ble_app_buttonless_dfu and ble_app_uart code.
I have done the changes...
Hello guys.
I am able to save an array to flash memory unfortunately I can not save a struct in flash. I am referring to this question Save struct to flash . However I...
Hi,
I'm a beginner in programming Nordic uC and I would like to know how to enable the watchdog in my application. Are there particular functions to call?
Thanks!
Hi,
We have a prototype application which requires an NRF52 based peripheral to be inside a metal cabinet and to connect via BLE to a central while maximising the link...
When calling access_model_application_bind() , NRF_ERROR_NOT_FOUND is returned?
I have had this working before, but after adding another server model I am getting the error...
Hi,
I am implementing modified DFU for nRF52832 which uses external flash memory. If power loss occures during update process, device then start update process from the...
Hello sir,
I am working on my final PCB design using nRF52832 chip. As per your reference Bill of material i use same part number for all components recommended by you. But...
I have a custom board with the nRF51822 QFAA . Schematic:
In order to compile the firmware, I'm using MinGW . As you can see, I'm also using the SDK 12.3.0 .
Finally...
