Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Suppose I configure RTC0 and RTC1 to have the same LFXO clock source (with a 30uSec tick) and start them in quick succession. Will their counters read the same value?
I...
I just started trying to get an IOT IPv6 application up and running. On the nrf51882 end, I have flashed the IPv6 COAP server. The LED on the device is happily flashing away...
Hi,
It looks like system (laptop windows 7) is not supporting more than two windows of RTT viewer simultaneously.
When I connect, third one, it disconnects, one of the...
Hi
The concept of setting the event_length (the time set aside per connection) was introduced post softdevice v3.0.0. To my understanding, with softdevice v3.0.0, the softdevice...
I have a android phone, and it says there's a FW update (1.1.0) for the thingy (it says I'm on 0.0.0). I confirm that I want it, but nothing happens. What can I try? I get...
We are using a nRF52840 (QIAAAA) on a custom board which replicates exactly the schematic used by the development kit (PCA10056). When using Segger RTT for debugging purposes...
I am using adv_report_parse to try and return the device names the scanner picks up. However device names are being printed repeatedly.
I have 4 to 5 devices around me...
Hi
The serial connection handler "ser_conn_handlers.c" may case an INVALID_LENGTH error when receiving Advertise Reports (or other long BLE events). The reason for this...
I have BLE Nitrogen. It is defined as a disk on which it can be dropped hex and it is loaded. Please explain in detail how to make hex which can be dropped on the device....
I have code running on a nRF52 device, with SoftDevice enabled, based on the example given in this topic:
devzone.nordicsemi.com/.../
This runs fine on its own, and...
Hello !
I am currently working on a custom board on which I don't need 32.768kHz. I want to use P0_1 as an interruption pin connected to a pushbutton. The button is connected...
Hi,
I am using IAR embedded version 7.40 and my board is nRF52840 PCA10056,while i was checking devices list in IAR IDE under NordicSemi i can see only nRF51 series devices...
Hey .My source code was compiled against SDK 8.0 now we need to upgrade the SDK to 10.0.
I have just copied the SDK10.0.0"components" folder to my project ( replaced the...
main.c
y_timer.c
y_timer.h
Hi,
I wanted to make the function that get timestamp like mills().
I made this code bellow.
It does'nt move well.
Main loop is unintentionally...
