nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi,
I am performing "just pairing" using peer manager ( SDK 11.0 ) in my custom board which uses nrf52 chip.
I am getting this events
PM_EVT_CONN_SEC_START,
...
Hi, I'm using nrf8001 nordic chip on my project. With some time on the nrf8001 chip begins to send the HW_ERROR with failure on ll_lm.s0.c and line 571. This not crash the...
Hi,
I am using the nRF52832 and I have been trying to meausre the centre frquency on a specturm analyser. But, the centre freq on the specrum analyser is 1.81GHz when it...
Hi,
I have a beacon that uses 4 AA batteries, each has 1.5V and 2600 mAh. When connecting the board to the PPK I get the attached measurements when doing a lot of scanning...
Hey guys. We are using the NRF52 with SDK 13.0.0.1-alpha.
If we connect the NRF52 to our own android or iOS APP we have some timing problems with notifications. When the...
I would like to reduce current consumption on my beacon and I wonder if it is possible to disable sending scan response. I know that it is not a huge difference in a single...
Firstly，the RedMi Note3 DFU failed used by dual bank，however Xiaomi3 Phone can DFU successfully.As the question link text mentioned,the process of the RedMi Notes3 Phone DFU...
Hello Nordic,
i am trying to interface BME280 with nordic nRF52 and SDK v 12.02 using twi_peripheral but i am unable to do it. here in example they are using ls75b whereas...
How do you setup "immediate Service Alert" Client on iOS, in order to get notified when an action is taken on the bluetooth peripheral ? (eg. Button press)
Hi all, I have an nRF52832 which is woken up every 15 seconds by an RTC to check for ESB broadcasts. The nRF52 will be powered continuously until the battery runs out, so...
I want to use AES ECB block present on nrf51 and nrf52 boards for resolvable private address (RPA) generation.
Are there any measurements about how much battery the...
I have an iot/coap environment setup and i want to read input voltage connected to p0.01.I can read the input in terms of resolution(0-1023).I can convert this values to voltage...
I have a project where I need both TWI instances as well as an SPI instance to be used with sdcard and fatfs libraries. When I try to compile I get the error: SPI1_TWI1_IRQHandler...
hi,everyone,I want to ask who know why sdk11.0 ble_ancs push message without push App Identifier?I look at the print, push the news started with tittle ,and the "p_attr -...
