I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
SDK12 does not have Pstorage. I want to show you how to add it.
Steps:
Copy the pstorage folder in SDK11 into the SDK12 \components folder.
Open...
Hello,
I've been working on a project for some time now and prototyping it with replacement atmel ic's like the at mega328 and bluetooth modules and other stuff in the...
My custom board sometimes freezed on initialization process of bootloader (SDK11 dual_bank_ble_s130) when after long running and reconnect the power.
However the symptoms...
I am running the ble_app_hrs example and it runs as expected.
However, I tried removing one or more of the services from services_init as well as the corresponding advertisement...
I implement a card emulation and the card itself doesn't conform to 14443A-3 crc check. I need to disable crc check on card selected event
NRF_NFCT->RXD.FRAMECONFIG...
I've been running a hand soldered prototype board for about a week in an outdoor location where it gets hot and cold (mainly hot), and I noticed it was no longer visible on...
I am trying to add the spi and twi drivers to the ble_app_template project, but I keep running into errors. I am using the SDK 12.2.0. How are we supposed to go about adding...
Problem:
In our project we have one peripheral which can be bonded to many phones at the same time (of cause) while they are still close to it, thus connected via OS. ...
I am trying to scan and connect to a Polar H7 HR belt (which I can do), with m_scan_mode = BLE_NO_SCAN. Once this happens, I understand they are supposed to bond, and at that...
In my low-power application I need to use advertising interval of few seconds (two or more) in order to get lifetime of a year with CR2450 battery. However, the Android application...
There's a great application nRF UART 2.0 that can be used like a terminal with a Bluetooth LE device implementing the "Nordic UART" service. Now I would like to store output...
I am using a nrf52832 with SDK 11.0.0 and sd132. I need to add in-flash storage to my application so I'm looking at the NVMEM documentation and the pstorage module. I understand...
Dear Sir/ Madam,
I want your suggestions and recommendation regarding to choose which one of your BLE development kit.
I want a Bluetooth development kit which has long...
Hello, I'm trying to update services list on central device after adding a new service. However, sd_ble_gatts_service_changed returns NRF_ERROR_NOT_SUPPORTED . After looking...
Hello,
In my application, I need to activate BLE during startup only if some conditions are met otherwise I put the nRF52 in SystemOff mode. BLE should not be activated...
