I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Dear Nordic Team,
We are using nRF52840 based module and using its ZigBee Radio. For one certification purpose, we need to know the max. pulse time (duration) for Tx and...
Hi again,
This is my project:
I have 3 nrf52832 kit and a Android phone. I want use my phone to control leds on those 3 boards. Because the phone dont support mesh, so...
Hi, I'm using nrf connect SDK v1.5.0 and I use SES to build and flash projects.
I use Visual Studio Code for only code editing environment. When I was using nrf5 SDK, I...
Hi ! I'm trying to access the beginning of a packet that is being transmitted, by accessing the SFD. My problem is that I'm not able to do it.
NRF got a function called...
Hi,
I'm currently trying to build a quick frequency spectrum scanning tool on an nRF52840 dongle. I want to sample RSSI on a list of channels as quickly as possible in a...
hello,
we're working with the nRF52833 and are experiencing some issue with the I2C interface during communication involving clock stretching. We're wondering if the errata...
Hello guys,
I am dealing with a problem, i have two tasks with two different spi instances, alone they work fine, but when i want to run both tasks they crash!!
Hi!
I met some issue ).
I use nrf mesh app on my phone and change it for my goals. I would like to get messages from nodes to phone via mesh. I read some posts that it...
Hi,
While developing an app which will connection to an IOS device via BLE - I've noticed an event called BLE_GAP_EVT_PHY_UPDATE_REQUEST.
I understand that this event...
Hi,
I'm using NRF52840 in order to connect to a mobile device, with PIN code.
Connection to Android is ok. The issue is with IOS.
IOS can't send the PIN code to my...
Hello, We're trying to optimize the data transfer rate from our nRF52832 based peripheral device to the mobile phone. Tested with two different BLE >= 5 Android phones we...
Hello, I ve made a custom nrf52832, but ive face a lot of problemes : when logs is on the BLE is off(its not advertising) , I m not able to see it on my app. when my module...
Hello,
I am using MacBook and would like to import Keil Projects into Segger Embedded Studio by following this guide , but finally I got an error is that
I have found...
I have some questions about nRF9160.
1. What is improved comparing to revision1? Only power consumption?
2. Is GPS sensitivity improved? In revision1, it is poor.
3...
Hello!
I use light switch example in a 52DK with a 4.1.0 mesh SDK. I modified the original project and implemented the custom element model for sending arrays via mesh....
