nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi, We have a smart product, which has two application scenarios. One is the use of BLE peripherals, similar to sports bracelets; The other is the 2.4g private protocol mode...
Hi Nordic team
How can I begin to develop the thread mesh? from the https://infocenter.nordicsemi.com/index.jsp I can run which example project
I had no found it from...
Hello .
I want send BLE data of sensor value.
So, I am using the central module(HM-10) And peripheral is nRF52832 of custom module.
Connection and data communication...
Hi
We are working on the FOTA based on http_application_update project. The hardware is Thingy91.
The issue is if we use the default the MCUBootloader on Thingy91(version...
Hi ,
I am working on nrf based project . I m trying to build my project using Cmd . I followed the steps given in link -
https://devzone.nordicsemi.com/nordic/nrf-connect...
Hello,
is it possible to localize the chip via the NB technology.? I red that this is supported by the NB standard.
When I switch on NB supporte systemmode the gps sample...
Are the accepted values of nrf52832 output power as below:
4, 0, -4, -8, -12, -16, -20, -30, -40
What we are most concerned about is whether -30dBm output power was available...
To the kind attention of Nordic support team,
We would like to delete BLE bond infos, only for test purposes. Being BLE not even activated and softdevice not used.
For...
My nRF52840 arrived yesterday and I started playing around with it. It is immediately recognized y nRFConnect v3.5 BLE App v2.4.0. The firmware on the device is 4.1.2 Jul...
Hi There.
I just downloaded a SDK for the wisol module that uses the nRF52832 and i can't get it to compile in Keil V5.31. Im getting this error:
Error: *** Project...
Hi
I am new on nRF52833 and want to try RF test for development.
I have a nRF52833_DK on hand with Direct Test(DTM) in nRF Connect(Descktop). However I am not success...
Dear Sir/Madam,
We are «SMART Solutions», Ltd. a startup from Tomsk, Russia.
Our company developed iBack Posture Corrector please see http://en.iback.online/ .
The device...
Hi Nordic team
I tested the example [802_15_4\wireless_uart\raw\first ] period 1s send 20 Byte data to example[ \802_15_4\wireless_uart\raw\second ]serial tool to printf...
Hi
I am working on a project based on Thingy91. Is there any sample application in NCS SDK to show the communication between the two SoCs on the Thiny91. I will need to...
Hi all,
I migrated my nRF52840 examples from SDK 15.2 to SDK 15.3 folder and when I tried to build
the examples and I discovered that nrfx_power_clock.c could not be found...
