Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello,
I am using PCA10040 development board based on nRF52832, Softdevice 6.1.0 & SDK 15.1.0.
On the Nordic website, I have verified that Softdevice v6.1.0 supports Chained...
What is the best practice for protecting against ESD for unused pins, should I leave them floating or ground them? I noticed in other posts here that it has been recommend...
Hi!
I use HID example and try to understand in a hid service init for why report_map_data[] with a table.
What is do this array? If I use keyboard example, I should get...
Dear Sir,
I am working on nrf52832.softdevice S132. SDK15.
I am getting the following messages when I try to connect to the peripheral using nRFConnect.
The error is...
Hi,
we are testing nrf52840 together with rfx2411n amplifier to extend the range.
The problem is that we have same range and same RSI values when testing with bypass mode...
Good afternoon,
I have purchased multiple nRF52840 Dongles and so far have successfully ran blinky peripheral and master (required to adopt PCA10056) examples.
I tried...
Hello Nordic
I am testing SEGGER EMBEDDED STUDIO and I think it is little buggy.
When i simulate NRF52 application without actual device (I can not
debug on hardware...
Hi,
I used SDK_15.1.0, secure_bootloader/pca10040e_uart.
Through PC uart,it update successfully .But boot through android(linux) uart,it returned 'invalid crc'.Can anybody...
Hello,
I am working on BLE Peripheral and Central part on SDK11 for a long while. Now i want to start with NFC.
I tried to go through nfc section in SDK14 but could not...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hi
I had used one nRF52 Kit(nRF52832+nRF5_SDK_14.2.0) to connect a BLE 6LoWPAN Border Router(Raspberry Pi 3B+Raspbian)
according to the IoT User Guide.
But in IoT applications...
i am using ubuntu 16.04
using eclipse photon IDE
nrf52_14.1.0 i am unable to run to run more than two threads can u please help me out in this
i am trying "nRF5_SDK_14...
Hi,
I am working with bonding process on Android App.
My problem is:
When I create bond to nrf51822, the process complete successfully. Then after a few seconds (3-5...
Dear Nordic Team,
Thanks for supporting .
I have a custom hardware for nRF52832 its working for nrf_beacon example but its not work with eddystone beacon example.
please...
