Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
I try onnrf52804 (nrf52840-DK) with SoftDevice V6.0.0
----------------------------------------------------------------------------------
ble_gap_scan_params_t s_scan_params...
Hi all,
I want to use the python scripts provided in application notes in nordic documentation to run DTM example flashed into nRF52840 SoC. So when I open command prompt...
In the infocenter, after searching for something, if you click on an item in "Search Results" (left hand panel), it brings up the associated page in the right hand panel....
Hello all,
I'm trying to do a "BLE scanner" in order to read non connectable advertisements. These advertisements can be PHY_CODED and PHY_1MBPS (classic BLE advertisements...
Hi everbody,
I'm using the BLE Database Discovery module to discover services and characteristics of a BLE peripheral. This works fine, except for one strange quirk:
When...
Dear Nordic Support Team,
I’ve bought an evaluation kit here : http://t-yuden.com/ut/product/category/module/EYSHJNZWZ.html
and i would like to program the chip, so i...
Hi,
I am scanning from my nRF52840 and connects to one peripheral and i have written code to get it's Device information(DIS) and i stored all these information in some...
I'm having trouble maintaining a connection between my nRF52832 and Raspberry Pi. I followed the step by step guide (making sure to use the correct IOT SDK for my board),...
I am gaining my expertise in Nordic. After learning from tutorials. most of the tutorials mentions to use master control panel. But I cannot able to scan using master control...
Hi!
I am currently developing an application for nrf52832 and am using the uart module with retarget.c for output over uart via printf().
Now a few days ago I added...
Hello everyone ,
We have done advertising and scanning(both in a single firmware) on nrf51822 using QFAC chip. using SDK 12. Now we want to switch our code to NRF51822 QFAA...
hi
I am trying to add Manufacturer specific data
ble_advdata_manuf_data_t manuf_data; // Variable to hold manufacturer specific data uint8_t data[] = "A"; // Our data...
Hi, when I provisioned the client and servers via provisioner to create mesh network, I can receive RSSI value from provisionee ,but after the provisionee disconnect to power...
I have a nRF51 DK. I am trying to sniff the Bluetooth connection between the smartphone and watch at Window 7.
Installed:
Wireshark 1.10.7
Sniffer (tried ble-sniffer_nRF51822_1...
The sdk_config.h configuration file for ble_app_hrs_freertos example contains following definition:
#define NRFX_GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS 1
This macro should...
