nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I am developing a program with BMI160 with this libraries , but I do not know to which it refers the following code at line 5 and 6: sensor.read and sensor.write.
It is...
I’m using the example “light switch” of SDK Mesh.1.0.1. In my case, i use nrf51 dk as client and three nrf51 dongles as servers but It doesn’t work.
I have tried to debug...
Hi everyone! I'm trying to generate a modulated continuous signal in a specific channel using nrf52832. I used a code made from radio_test example that follows. The problem...
when i program the code firstly , the device is not broadcast,But the other is running well. the output log is correctly.
when i reset the device several times , the device...
Hi, I have done some developing for nRF51822 with Keil before and now I have started out with a new project using Segger so of course I wanted to use the lastest SDK with...
While writing a hardware (I2S) assisted software UART I have noticed that the SDK 14.2 seems to be missing two enums for 32MDIV30 and 32MDIV32
Below is a diff from my private...
Currently I am scanning with a window of ~23ms and an interval of ~33ms. I am also advertising with an advertising interval of ~330ms. Using radio events, I notice that the...
Hi,
I am seeing a couple of issues in my Android mobile app while doing a DFU:
1. The DFU stops in the middle with this log on the debugger
I/art: Starting a blocking...
now i use nRF52832 and my using paccage is SDK14.0.0
i could send data from phone to nRF52832.
next i wanna send data from nRF52832 to phone.
but i don't know where to...
nrf52832
SDK 14.2
NVMC and SD backend both
Hi,
I had a question about the nrf_fstorage_read function. In a previous answer , it was mentioned that fstorage_read function...
Hello,
on GitHub I foudn an out of the box example for bluetooth mesh with multiple Thingy-boards ( https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo ). The...
Dear Nordic Team,
Thanks for supporting.
If any possible to add manufacturer data in example experimental_ble_app_blinky in advertisement. i am using SDk11 and my hardware...
Hello,
I have been trying to read the temp , hum and pressure value using BME280. The problem i face is i get the same value constantly and it doesn´t change.
I am trying...
My SDK version is NRF51_9.00, softdeive 130, board nrf51822.
We want to confirm some questions about BLE muti connection
1. When NRF51 is scanning, could it connect with...
Hello everyone,
This is the second time that I've had the problem I am about to describe. I fixed it, and now it is broken again. I am fairly certain that it is not (only...
