Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
I am working with the nRF52832 pca10040 devkit, and when I program the softdevice with the nRFgo studio, the only version that shows the firmware after programming is S132_nRF52_2...
Hi,
we are using nRF51822-QFAA in our project which is based on the PCA10000-nRF51822 Development Dongle 2.0 - layout of radio part is almost the same. I'm also using sdk...
I need to read variable length blocks from an I2C slave using a TXRX transfer. The length of the following data is given in the first read data byte, similar to SMbus Is there...
I installed Bluetooth Developer Studio , (BDS), which appears to offer a way of setting up a custom profile without have to spend too much time on writing low level code....
Dear Everyone.
Hi, I develop nrf51822 with DK PCA10028. I have been optimizing the power consumption to some extent. But now I am very confused.
I use S110 softdevice...
Hello Everyone
We have a project using the Feather 32u4 BLE chip to communicate with an IONIC Application on Android.
And the huge problem is that i'm really really...
Hi,
I am interfacing HX711- 24 bit ADC for Weigh Scale to calculate weight which has
DOUT and PD_SCLK for Digital Output and Digital Input. I have the working Arduino code...
With Eddystone example in SDK12.0.0 I am trying to configure with nRF Beacon for Eddystone application but every time I change the URL " www.nordicsemi.com/" to something...
I use SPI connection according to the table .
I want to press the button 4 on tx (P.06) to transfer "hello", to write down the answer of rx(P.08) in the file on sd card in...
Hi
I'm using nrf51 to notify some data to an andriod device. I set the connection interval of my nrf51 program to 7.5ms. And I need to send 100 packets per second (20 bytes...
Hi Admin.
How can i calculate distance using RSSI. is there any existing method available? i tried statically(like 35-40=1m 40-45=2m) but i dont know actual method to get...
Hi all,
I am trying to add the iOSDFULibrary library to an existing Objective-c project via Cocoapods (Xcode 8.2.1 - target iOS 10).
I have followed the steps reported...
Hi
I've just done a few tests with the FDS system of the SDK12.2. My observation is, that the FDS doesn't properly use all assigned flash pages to reach a maximal lifetime...
Hi,
I am quite new to nRF51 development so please excuse me for my mistakes or not using right words if any. I have some code that fully works on the official nRF51 DK...
