I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hey,
We're are newbies with Nordic and are trying to program BLE HRS example code to run straight on the nRF52832 (instead of the PCA10040 target).
In order to do so we...
Hi everybody! I am here again bothering you with probably silly questions. I have, on my smart beacon kit, an application that uses an ADC and then sends the converted value;...
`Hi Guys,
My project requirement is that first time i have to bond and connect my nRF8001 BLE with peer device, once connected i have to find peer device address, after finding...
Hi everyone,
I was not able to find a full example in the SDK or online on initializing ANT to work with burst mode. Also, I was wondering if it's possible to setup ANT...
Hello,
I have a design where nrf51422 works as companion chip together with an other uC as main controller (STM32F4).
I need to reset the NRF from the main controller...
Hi,
For our new product we are using nRF52832 chip for BLE and NFC. We have a query regarding the NFC section which is listed below-
Please refer the recommended EMC filter...
I have captured the ble packet showing as the screenshot by using the ble sniffer(win7 ) and wireshark.
But I did not understand the meaning of delta time (such as end to...
Hello!
I would like to whitelist a peripheral when -60 dBm RSSI is achieved (this means that central will bond to peripheral by proximity) but later data exchange must...
Hi all, i have an application with a smart beacon kit; i won't resume the whole project because it's long and boring, i will just say that i have a service that every 100...
Hi,
I'm using the S110 v8.0 on a nrf51422 together with our own scheduler with a few lines left from SDK v8.1.
I'm sending out advertising containing some extra data and...
Dear
As far as I know, the nRF51822 has the Pin Crossbar feature that weu can chose and connect
any GPIO pins as second UART.
I need to talk to two UART peripherals...
Hello Everyone,
I have created an schematic for m custom prototype using NRF51BLE with Sigfox Radio chip whenever i press the button on the NRF51i has to send message to...
Hello,
is there a trick, how the Radio peripherals device address match feature could be used to implement those advertising filter policies that filters based on the PDU...
I want to program the ARM MCU in the nRF51822 Development Kit for my own purposes and then send the processed data using the BLE module in the kit to another nRF51822 Development...
I have been using this mode to init the app_uart_fifo code on SDK8 for a while now and when moving over to the SDK11 code I was in the app_uart_fifo.c code and it's radically...
