I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
I have create software for the nrf51822 (slave) that has
I also create a PC application using the master emulator api that implements the master
Data from the master...
Hello,
Does anybody know what I could be doing wrong either on peripheral or PC when my program on PC reports this error?
I am in the process of writing an application...
Good morning. Thanks for reading. I am brand new to development on Nordic platform but fairly experienced with ARM Cortex, GCC, IAR, Eclipse, etc.
I have a the PCA10003...
Hey guys. I'm very new to Bluetooth 4.0 (actually Bluetooth in general), but I'm hoping to be able to use a Fujitsu MBH7BLZ02-109004 module with an nRF51822 in a product I...
I am attempting to measure battery voltage through the ADC, but am getting inaccurate results. In my setup, I have a 4.2 V battery divided down to the bandgap range using...
HI all:
I am using the nrf24le1.And i confuse about the recive and transmission address in rf transceiver.
What do we use the address to do usually.It will be wonderful...
Copy nrf51.cdb to "C:\Keil\UV4"
Copy nrf51xxx.flm to "C:\Keil\ARM\Flash"
Set the keil project-device to nRF51822(data base : Nordic nRF Series Devices)
This is...
Hi
Is there a documentation of the nRF51822 sniffer interface? e.g. communication structure, command format, captured messages structure etc?
Thanks
Yaron
I'm trying to set up a network where 1 - 4 BLE devices wirelessly talk to a computer. I'm using an arduino connected to the BLE shield.
The computer is a Winows 7 laptop...
Hi,
I'm creating a project on nRF51822 chip and I have a problem with disconnection. In my program I want to disconnect with master after some time e.g. 30 seconds. I'm using...
I'm unable to write my application code to the flash of an NRF51922 (QFAACAA). NRF Studio will let me flash the hex file but it fails verification. If I try programming in...
I have a question, can nRF51822 operate in regular Bluetooth mode like a Bluetooth 2.1 device?
If answer is no then, is there any product from Nordic that operate as Classic...
Hi developers,
I've finally got the nrf51822 working and advertising a good signal to the dongle. :)
After doing all the steps in the NAN-36 pdf-file I hoped that pressing...
Hi all,
I'm using Timer2 while having the SD enabled, and I'm having some problems. I don't seem to be able to reliably set the periodicity of the timer. No matter what I...
I've spent quite a while getting Eclipse on Mac OSX working. I started with the original makefile but have come up with, finally, a working native Eclipse build which does...
