Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
We are working on a board with nrf5340. We are running the nrf5340 in normal voltage mode. So, we have connected the VDD lines to 3.3V. Since we are using USB signals...
how can I put nrf52832 in the system on sleep mode on advertising timeout?
Currently, on timeout, the device is going in system off mode and restarting on interrupt.
Hello,
I noticed that you improved the hardware design in version 1.4. Is it still neccessary to use a bias tee for an external GPS? https://devzone.nordicsemi.com/f/nordic...
Hello, I am still learning about BLE devices and have a quick question regarding the Generic Access Profile. I understand that GAP defines 2 things:
The discoverability...
Per the notes on https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/Download#supl-c - "Highlight: Updated library made to work with the new modem library...
nRF52832 SDK 17.2
We are trying to get the packet loss/error information on a per channel basis. It is similar to what is being discussed in https://devzone.nordicsemi.com...
I am using NRF dongle in window PC and scanning tags with nRF connect->Bluetooth Low Energy . Is there any way to change the scanning parameters of nRF connect for windows...
Hi,
I have downloaded the nrf5 Sdk 17.02 from the website. And I have found the ble_gls example in ble peripheral example part.
Kit : nrf52832
1. Can you please explain...
Hi,
I am using SDK 17.0.2. I am using write and notification characteristics. There is a write and notification communication between iOS app and device. After successful...
I'm running into a problem where my softdevice is triggering the fault handler but only when I'm also using the USBD. The panic info is below, I've tried to double and triple...
I am working with signled door sesnor and it supports ZigBee 3.0 as it has an install code and mac address on the side of the sensor in the form of a QR code. When I run the...
We are using the latest pc-ble-driver with SoftDevice v6.1.1 and latest connectivity firmware on an nrf52832 (s132) which is connected via usb-uart.
We were previously using...
Hello!
I am flashing software over USB as I do not have a 10-pin JTAG cable yet. After I flashed a sample file on to the Thingy91s SIP it is no longer showing up in nRF...
