I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello,
I want to store some data(coming from the ADC) in flash for nrf51822.
is it possible?
have you any example to show me?
Thanks a lot and best regards
...
I modified the FW "ble_app_uart" using the example "\ nRF5_SDK_15.2.0_9412b96\ examples \ ble_peripheral \ ble_app_uart \ " . I added the pairing function and "delete_bonds...
Hi,
I have got the problem with using BMD-340 demo SPI commuination for many days.
+----------------------------+ | | | Problem Describtion | | | +-------------------...
Hi.
Using SDK13, nrf52, and the awful IDE Segger , I keep getting this error no matter what kind of code or project with PWM I use :
Undefined reference to nrf_drv_pwm_init...
Dear All,
I would like a simple way to read the voltage on one ADC pin without using any "adc_event_handler"-like solution.
I tried
reading=nrf_adc_convert_single(NRF_ADC_CONFIG_INPUT_2...
I'm trying to finish a handmade custom board I started. I had previous problems with the crystals, and a few others, but right the thing seems to be working ok. At least I...
NRF52832 on SDK 16.0.0, softdevice s132 (using SES) When writing constant value with FDS it saves normally, but when I try to write variable it saves some garbage. Here is...
Hi,
Is it possible to give 3.3V to the Vdd pin of my nrf52840 to change the reference voltage of saadc to 3.3V ? Do I have to change any configurations for the same?
Hello community
I want to advertise when physical pin 0.24 is high, and stop advertising when pin 0.24 is low. For this, I based my code on the Beacon Transmitter Sample...
Usually, I programmed the Thingy 91 with the nRF connect Programmer (right now version v.3.3.3). As my Thingy did not work with the asset tracker software and only with the...
Hi,
I am trying to integrate an UARTE application code with OpenThread example(thread_mqtt_sn_client_publisher_pca10056) on my nRF52840. My application code uses UARTE0...
Dear Sir/Madam,
I need help. I am using UART to send the data in the mesh topology .and I configured mesh using light_switch source code. is it enough to send data using...
I am trying to interpret the values in the INFO.VARIANT register for the nRF52840. The datasheet states "Build code (hardware version and production configuration). Encoded...
Hi,
After following the steps for building the documentation, I always get the following error:
"CMake Error at CMakeLists.txt:92 (add_subdirectory): add_subdirectory...
